P02D0: Cilinder 3 — aanleren van de offset van injector A op de ondergrens
Wat te doen
Ask for a leak-back test across all the injectors, not just this cylinder. It compares them against each other, takes minutes, and tells you whether one injector has worn out or the whole set is on its way — which is the difference between a repair now and the same repair again in six months.
Check the engine oil level and smell it. A worn injector on this cylinder puts diesel into the sump, and oil above maximum or smelling of fuel needs dealing with promptly rather than at the next service.
Ask whether the calibration codes are correct, since that is the free thing to eliminate before any part is bought.
Do not defer this. The module has run out of trim, which means the wear has been developing for a long time already.
Wat deze code betekent
The correction the module applies to cylinder 3's injector has reached the bottom of its adjustment range.
Cylinder 3 over-delivers, the module has trimmed it down as far as it is allowed to, and the imbalance persists.
The over-delivery half of this family has one cause that dominates all the others on a high-mileage engine: a worn injector that no longer seals. A common rail injector holds back fuel at very high pressure with a needle and seat measured in microns. As the seat wears, the injector both delivers more than commanded while open and leaks after it closes — and the module sees the sum of the two as excess fuelling on that cylinder.
The leak-back test is what distinguishes this from a calibration problem, and it is the measurement worth insisting on. With the return lines instrumented, an injector leaking past its seat returns visibly more fuel than its neighbours. It takes minutes and it answers the question definitively — where the calibration route only tells you what was programmed.
A worn injector that over-delivers puts diesel down the cylinder wall. Check the oil level and smell: a rising level or a strong diesel smell means fuel is reaching the sump, which dilutes the oil and, in the worst case, lets the engine run on it.
Where several injectors leak back excessively, the set is worn and replacing one is a short-term repair.
Waarschijnlijke oorzaken
Begin hier
- Brandstofinjectoren versleten of lek · specialistisch
Minder vaak
- Injector gemonteerd zonder de kalibratiecode in te voeren · specialistisch
- Brandstofinjector uitgevallen · specialistisch
- Gereviseerde injector gemonteerd met zijn oorspronkelijke code · specialistisch
Symptomen
Betrokken onderdelen
Informatie, geen instructie
CarGeek is een naslagwerk, geen werkplaatshandboek. De pagina's zijn geschreven op basis van openbare bronnen en van wat anderen hebben ondervonden, nooit op basis van de servicedocumentatie van de fabrikant zelf, dus ze kunnen onjuist of onvolledig zijn voor jouw specifieke voertuig. Een deel van wat erin staat brengt echt gevaar met zich mee: hoogspanning, brandstof onder druk, opgeslagen energie en hete of bewegende delen.
Laat alles waarnaar je wilt handelen eerst controleren door iemand met een technische opleiding, aan de hand van de eigen procedure van de fabrikant voor jouw voertuig. Niets hier vervangt die procedure.
Ervaring uit de community
Wees de eerste die dit beschrijft
Hierover is nog niets geplaatst. Wat je ook hebt gevonden, het is het opschrijven waard — zelfs een doodlopend spoor bespaart iemand dezelfde middag.
Wat het de moeite waard maakt:
- De auto — merk, model, bouwjaar en motor. Dezelfde storing gedraagt zich per auto anders.
- Wat je gemeten hebt, niet alleen wat je vervangen hebt.
- Wat het echt verholpen heeft — of dat niets dat deed, wat ook nuttig is om te weten.
Inloggen of een account aanmaken om toe te voegen wat je hebt gevonden over P02D0.