P2C30: Fusível A do circuito primário das bobinas de ignição
Não continue dirigindo
Stop driving if the engine warning light is flashing. A flashing light means unburnt fuel is pouring into the catalytic converter, and that destroys it in minutes — turning a modest repair into a very expensive one.
Expect the engine to be shaking badly and running on fewer cylinders than it has. A fuse feeding a group of ignition coils has blown, so those cylinders have no spark at all.
Do not just replace the fuse and carry on. It blew because something drew too much current — a failed coil, a chafed wire earthing out, or water in a connector. A new fuse without finding that will blow again, sometimes immediately.
Have the car recovered rather than driven if it is more than a short distance.
O que este código significa
The fuse feeding ignition coil primary circuit A has failed.
This code names a fuse, which makes it unusually specific — and unusually likely to be misread as trivial.
Ignition coils draw substantial current on their primary side, and on engines with many cylinders that load is split across more than one fused feed. The letter says which group has lost its supply, and the consequence is immediate: the cylinders on that fuse have no spark at all.
So the symptom is not subtle. Expect a serious misfire, an engine running on some of its cylinders, heavy shaking, and a flashing engine warning light. A flashing light means unburnt fuel is reaching the catalytic converter, which destroys it in minutes rather than months — this is one of the few codes where continuing to drive has an immediate and expensive cost.
A fuse is a symptom, not a cause. It blew because something drew more current than it should: a coil with a shorted primary winding, a chafed harness earthing against the engine, or water in a connector. Replacing the fuse without finding that means replacing it again, usually within minutes.
Why this page exists when its neighbours do not. Nothing in the public web documents this block — four independent searches established that on 2026-08-10. This code is written because a manufacturer named it, with its definition, in a technical service bulletin filed with the US road safety regulator, and that OEM wording agrees with the standard's own enumeration. Its neighbours have no such document, so they remain undocumented rather than guessed.
Causas prováveis
Comece aqui
- Fusível queimado ou alimentação inoperante · fácil
- Bobina de ignição defeituosa · moderado
- Chicote gasto por atrito no motor ou suporte · moderado
Menos comum
- Infiltração de água no conector · moderado
- Atuador em curto derrubando a alimentação · especializado
Sintomas
Componentes envolvidos
Informação, não instrução
O CarGeek é uma referência, não um manual de serviço. Suas páginas são escritas a partir de fontes públicas e do que outras pessoas constataram, nunca a partir da documentação de serviço do fabricante, de modo que podem estar erradas ou incompletas para o seu veículo específico. Parte do que descrevem envolve risco real: alta tensão, combustível sob pressão, energia acumulada e peças quentes ou em movimento.
Antes de agir com base em qualquer orientação, peça a verificação de uma pessoa com formação técnica, seguindo o procedimento do próprio fabricante para o seu veículo. Nada aqui substitui esse procedimento.
Experiência da comunidade
Seja o primeiro a documentar isto
Ainda não há publicações sobre isto. Vale a pena anotar tudo o que você descobriu — até um beco sem saída poupa a mesma tarde de outra pessoa.
O que faz valer a leitura:
- O carro — marca, modelo, ano e motor. A mesma falha se comporta de forma diferente em cada um.
- O que você mediu, não só o que trocou.
- O que realmente resolveu — ou que nada resolveu, o que também vale saber.
Entrar ou criar uma conta para adicionar o que você descobriu sobre P2C30.