P2672: Смещение момента ТНВД
Что делать
Expect the engine to be noisier than usual — a harder, more rattly note — along with smoke, poorer economy and less power. It is not immediately damaging, but it should not be left, because badly timed combustion is hard on pistons and bearings over time.
Before anyone quotes for an injection pump, ask for two much cheaper things to be checked, in this order:
- The fuel filter and fuel supply. Many pumps use their own internal fuel pressure to advance timing, so a restricted filter genuinely retards injection timing and sets this code. It costs very little and takes minutes.
- The mechanical timing — the belt or chain, its tensioner, and the pump drive. If the belt or chain has ever been replaced, say so. A tooth out at that point leaves the engine module quietly correcting for it for years until it runs out of adjustment, which is exactly what this code is.
An injection pump is one of the most expensive parts on a diesel, and it is often replaced for a code that a filter or a timing correction would have cleared. Ask what has been ruled out.
Что означает этот код
The correction the module applies to injection timing has drifted beyond the range it is allowed to use. The pump is delivering fuel at a moment far enough from the commanded one that the module can no longer trim the difference away.
Injection timing on a diesel is not a setting so much as a running negotiation. When fuel enters relative to the piston's position governs almost everything that matters: how much of it burns, how hard the pressure rise is, how much soot and how much oxides of nitrogen come out, and how the engine sounds. The module commands a moment, watches the result, and holds a learned offset to account for the pump's own tolerances, wear and temperature. This code says that learned offset has run out of room.
Two very different things produce it, and the order to check them in is the reverse of the intuitive one.
Mechanical timing is the first, and it is the cheaper answer. A timing belt or chain fitted a tooth out, a stretched chain, a worn tensioner or a pump drive that has slipped moves the whole relationship between crankshaft and pump. The module then spends its entire offset compensating for an assembly error — and because it compensates successfully at first, the engine can run acceptably for a long time before the offset finally runs out. A vehicle that has had timing work at some point in its history and set this code later is that until proven otherwise, and it is worth asking whether the belt or chain has ever been touched.
Wear inside the pump is the second — the metering assembly, the timing advance mechanism, the internal transfer pressure that many pumps use to advance timing hydraulically. Low transfer pressure retards timing exactly as though the pump were mistimed, and it is caused by wear, by a restricted supply, or simply by a blocked fuel filter.
So the filter and the fuel supply come before the pump. A restricted filter is a genuine cause of this code, costs almost nothing, and is checked in minutes — while a pump is one of the most expensive parts on a diesel engine and is very often replaced on the strength of a code that a filter would have cleared.
Вероятные причины
Начните отсюда
- Забитый топливный фильтр · простой ремонт
- Ремень или цепь ГРМ установлены неправильно · ремонт для специалиста
- Изношенный дозирующий узел ТНВД · ремонт для специалиста
Встречается реже
- Цепь ГРМ вытянулась · ремонт для специалиста
- Низкое давление подачи топлива · ремонт средней сложности
- Подсос воздуха в топливную магистраль · ремонт средней сложности
Симптомы
Задействованные компоненты
Информация, а не инструкция
CarGeek — это справочник, а не руководство по ремонту. Его страницы составлены по открытым источникам и по опыту других людей, но не по сервисной документации производителя, поэтому для вашего конкретного автомобиля они могут быть неверными или неполными. Часть описанного связана с реальной опасностью: высокое напряжение, топливо под давлением, накопленная энергия, горячие и движущиеся детали.
Всё, по чему вы собираетесь действовать, сначала проверьте с человеком, имеющим техническую подготовку, по собственной процедуре производителя для вашего автомобиля. Ничто здесь не заменяет эту процедуру.
Опыт сообщества
Напишите об этом первым
Об этом пока ничего не опубликовано. Всё, что вы выяснили, стоит записать — даже тупиковый путь сэкономит кому-то те же полдня.
Что делает такой отчёт полезным:
- Автомобиль — марка, модель, год и двигатель. Одна и та же неисправность ведёт себя на каждом по-своему.
- Что вы измерили, а не только что заменили.
- Что действительно помогло — или что не помогло ничто, это тоже стоит знать.
Войти или создать учётную запись для добавления того, что вы выяснили по теме P2672.