P2135: Корреляция напряжений датчиков или выключателей A и B положения дросселя либо педали
Не продолжайте движение
The car will be in reduced power or refusing to rev. Before agreeing to a throttle body or pedal assembly — neither is cheap — ask whether the five-volt reference and the ground were measured at the connector. Both sensors share those, so one bad supply makes two good sensors disagree, and that is a much smaller repair. If other unrelated sensors are also faulted, that points the same way.
Что означает этот код
Position sensors A and B disagree. This is the code the whole redundancy arrangement exists to produce, and it is among the most commonly misdiagnosed in the P2 range — because the obvious reading of it is wrong more often than it is right.
What it means. Sensors A and B are the deliberately-mismatched pair described under P2104: different slopes, or one rising while the other falls, so that no single fault can move both in a way that still looks consistent. The module compares them continuously. When they disagree beyond tolerance, it knows one of them is lying and — critically — it cannot tell which. So it distrusts both and withdraws throttle authority, which is why P2104 or P2106 usually appears alongside.
Why the obvious reading is wrong. "The sensors disagree, so a sensor is faulty" skips the thing they have in common. Both are fed from the same five-volt reference and share a ground, usually through the same connector. If that reference sags, or the ground develops resistance, both sensors shift at once — and because they have different slopes, they shift by different amounts. The correlation fails. Neither sensor is faulty. The corpus makes this argument at length under P0641 and it applies here exactly.
Why it matters financially. On a throttle body, the two sensors are integral and not separately available, so "replace the sensor" means replacing the whole throttle body. On a pedal, the same is true of the pedal assembly. Neither is cheap, and a five-volt reference fault or a corroded shared connector costs a fraction of either.
So the order is: measure the reference voltage and the ground at the connector, check the connector itself, and only then look at the sensors. If other unrelated sensors are also reporting faults, that is the shared-supply case confirming itself and the sensors here are almost certainly innocent.
Вероятные причины
Начните отсюда
- Отказ опорного напряжения питания датчика · ремонт средней сложности
- Разъём окислен или неплотно посажен · простой ремонт
- Плохое соединение массы датчика · ремонт средней сложности
Встречается реже
- Неисправный датчик положения дросселя · ремонт средней сложности
- Неисправный датчик положения педали газа · простой ремонт
- Отложения нагара в дроссельном узле · простой ремонт
Симптомы
Задействованные компоненты
Информация, а не инструкция
CarGeek — это справочник, а не руководство по ремонту. Его страницы составлены по открытым источникам и по опыту других людей, но не по сервисной документации производителя, поэтому для вашего конкретного автомобиля они могут быть неверными или неполными. Часть описанного связана с реальной опасностью: высокое напряжение, топливо под давлением, накопленная энергия, горячие и движущиеся детали.
Всё, по чему вы собираетесь действовать, сначала проверьте с человеком, имеющим техническую подготовку, по собственной процедуре производителя для вашего автомобиля. Ничто здесь не заменяет эту процедуру.
Опыт сообщества
Напишите об этом первым
Об этом пока ничего не опубликовано. Всё, что вы выяснили, стоит записать — даже тупиковый путь сэкономит кому-то те же полдня.
Что делает такой отчёт полезным:
- Автомобиль — марка, модель, год и двигатель. Одна и та же неисправность ведёт себя на каждом по-своему.
- Что вы измерили, а не только что заменили.
- Что действительно помогло — или что не помогло ничто, это тоже стоит знать.
Войти или создать учётную запись для добавления того, что вы выяснили по теме P2135.