P2135: Korrelation zwischen den Spannungen von Positionssensor oder -schalter A und B von Drosselklappe oder Pedal
Nicht weiterfahren
The car will be in reduced power or refusing to rev. Before agreeing to a throttle body or pedal assembly — neither is cheap — ask whether the five-volt reference and the ground were measured at the connector. Both sensors share those, so one bad supply makes two good sensors disagree, and that is a much smaller repair. If other unrelated sensors are also faulted, that points the same way.
Was dieser Code bedeutet
Position sensors A and B disagree. This is the code the whole redundancy arrangement exists to produce, and it is among the most commonly misdiagnosed in the P2 range — because the obvious reading of it is wrong more often than it is right.
What it means. Sensors A and B are the deliberately-mismatched pair described under P2104: different slopes, or one rising while the other falls, so that no single fault can move both in a way that still looks consistent. The module compares them continuously. When they disagree beyond tolerance, it knows one of them is lying and — critically — it cannot tell which. So it distrusts both and withdraws throttle authority, which is why P2104 or P2106 usually appears alongside.
Why the obvious reading is wrong. "The sensors disagree, so a sensor is faulty" skips the thing they have in common. Both are fed from the same five-volt reference and share a ground, usually through the same connector. If that reference sags, or the ground develops resistance, both sensors shift at once — and because they have different slopes, they shift by different amounts. The correlation fails. Neither sensor is faulty. The corpus makes this argument at length under P0641 and it applies here exactly.
Why it matters financially. On a throttle body, the two sensors are integral and not separately available, so "replace the sensor" means replacing the whole throttle body. On a pedal, the same is true of the pedal assembly. Neither is cheap, and a five-volt reference fault or a corroded shared connector costs a fraction of either.
So the order is: measure the reference voltage and the ground at the connector, check the connector itself, and only then look at the sensors. If other unrelated sensors are also reporting faults, that is the shared-supply case confirming itself and the sensors here are almost certainly innocent.
Wahrscheinliche Ursachen
Hier anfangen
- Referenzspannungsversorgung des Sensors ausgefallen · mittel
- Korrodierter oder loser Stecker · einfach
- Schlechte Masseverbindung des Sensors · mittel
Seltener
- Drosselklappenpotentiometer defekt · mittel
- Fahrpedalstellungssensor defekt · einfach
- Rußablagerungen im Drosselklappenstutzen · einfach
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P2135.