P01D6: Zylinder 6 — Funktion des Einspritzzeitpunkts, zu weit nach früh
Was zu tun ist
Ask two questions before agreeing to any work: how many cylinders are affected, and in which direction. One cylinder means that injector. All of them means something shared, like fuel or timing. A mixture of early and late usually means the injector calibration codes are mismatched — which is corrected with a laptop rather than with parts.
Say whether the engine knocks or sounds harsh under load, which fits this fault.
If an injector must be replaced, ask for the leak-back figures on all six and the labour to reach them. Doing a worn set together is considerably cheaper than one at a time on a six-cylinder engine.
Do not run it like this indefinitely, since early combustion loads the piston and bearings at the wrong point in the stroke.
Was dieser Code bedeutet
Combustion on cylinder 6 is happening earlier than the module commanded.
This is the last member of the family, and it is a reasonable place to record what the eleven codes are worth read together rather than one at a time.
The direction tells you the mechanism. Retarded means something is slowing the burn — a late-opening or restricted injector, low compression, a dead glow plug, low rail pressure. Advanced means something is starting it early — a leaking injector, an inaccurate pilot injection, over-volatile fuel, or a hot spot.
The distribution tells you the scope. One cylinder is local. All cylinders together is shared hardware — the timing drive, rail pressure, or the fuel in the tank. A mixture of both directions across several cylinders is mismatched calibration codes, which is a laptop fix rather than a parts bill.
Those two questions — which direction, and how many cylinders — narrow this family faster than any test, and both are answered from the stored codes before anything is touched.
For this code specifically, on a straight six, the far-end position that makes its retarded sibling a chain suspect makes this one an injector suspect: chain stretch retards, it does not advance. So an over-advanced code on the last cylinder points back at that injector or its pilot delivery rather than at the timing drive.
Access and labour dominate the decision on a six, so ask for the whole set's figures before committing to one injector.
Wahrscheinliche Ursachen
Hier anfangen
- Einspritzventile verschlissen oder undicht · Fachwerkstatt
Seltener
- Injektor ohne Eingabe seines Kalibrierwerts eingebaut · Fachwerkstatt
- Rußablagerungen im Brennraum · Fachwerkstatt
- Verunreinigter oder minderwertiger Kraftstoff · mittel
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P01D6.