P06E4: Wecken des Steuergeräts — Stromkreis, Funktion
Was zu tun ist
Mention whether the battery goes flat when the car is left standing for a few days. That is the commonest sign of this fault — a module being held awake instead of going to sleep — and it is genuinely useful information because it points diagnosis straight at the cause.
Also mention anything electrical that works intermittently or seems dead until you use something else first. That is the opposite half of the same fault.
Mention any damp in the car — a wet footwell, a boot that smells musty, a blocked sunroof or scuttle drain. Water in a connector is a classic cause of a module being held awake, because it leaks just enough current to look like a wake signal.
Mention any accessories fitted after purchase, such as a dashcam, tracker or alarm, since those are frequently wired to permanent supplies and interfere with sleep.
Was dieser Code bedeutet
The circuit that wakes a control module from sleep is not performing correctly.
Every module on a modern vehicle sleeps, and understanding why explains this code. A car parked for a fortnight must still start. With dozens of modules each drawing even a small current, a vehicle that never slept would flatten its battery in days — so modules shut down to microamps and are woken by a signal when needed.
Wake-up happens by several routes: a door handle touched, the key approaching, a bus message, or a hard-wired wake line from a gateway. This code says that route is not working as it should.
The two failure directions have completely different symptoms, and identifying which is happening is the whole diagnosis.
- Failure to wake. A module stays asleep when it should be awake, so a system is simply dead until something else wakes it. The classic report is 'it works sometimes' — the module woke by another route on those occasions.
- Failure to sleep. The circuit holds the module awake, and the battery goes flat over a few days of standing. This is by far the more noticeable of the two.
A parasitic drain complaint with this code stored is not a coincidence. Read this code as the likely cause and check what is holding the wake line active rather than hunting fuses at random.
Water in a connector is the classic cause of a permanently held wake line, because it provides exactly the small leakage current a wake input responds to.
Wahrscheinliche Ursachen
Hier anfangen
- Wasser in den Stecker eingedrungen · einfach
- Korrodierter oder loser Stecker · einfach
- Ruhestrom durch ein Zubehörteil · mittel
Seltener
- Datenbusleitungen beschädigt · mittel
- Softwarefehler im Steuergerät · Fachwerkstatt
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P06E4.