P0DE6: Zellspannung des Batteriepakets — Niedrig
Nicht weiterfahren
Do not try to charge or jump-start the vehicle, and do not let anyone else. A traction battery taken below its safe floor can develop an internal short that causes a fire hours after it appears to have recovered. Have it recovered to a shop equipped for high-voltage work and tell them the pack was deeply discharged. If the car is stored for long periods, keeping it around half charged prevents this.
Was dieser Code bedeutet
One or more cell groups in the traction battery has fallen below its minimum safe voltage.
This is one of the few codes in the corpus where the correct advice is genuinely "do not attempt to recharge it", and the reason is chemistry that has no equivalent in any other battery a driver has met.
A lithium cell has a floor as well as a ceiling. Below roughly two and a half volts the copper current collector inside the cell begins to dissolve into the electrolyte. When the cell is then charged, that dissolved copper plates back out — in the wrong places, including as metallic bridges across the separator between the electrodes. The cell may appear to recover and hold charge normally. What it has acquired is an internal short waiting to develop, and that is the mechanism behind battery fires that begin hours or days after a charge finished, with nothing plugged in.
So a deeply discharged pack is not a flat battery. The manufacturer's instruction on most vehicles is that a pack taken below its floor must be assessed rather than revived, and the car will usually refuse to charge it — which is the protection working, not a fault to be worked around.
How a pack gets here is worth knowing, because it is nearly always avoidable. Long-term parking at a low state of charge is the classic route — a lithium pack self-discharges slowly, and a car left for months at 10% arrives at zero. A balancing circuit stuck on (P0DAD) does the same thing to a single group while the pack as a whole looks fine.
Wahrscheinliche Ursachen
Hier anfangen
- Schwache oder ausgefallene Zellgruppe im Batteriepaket · Fachwerkstatt
- Tiefentladen nach langer Standzeit · mittel
- Zellsymmetrierschaltung ausgefallen · Fachwerkstatt
Seltener
- Sensormodul des Batteriepakets defekt · Fachwerkstatt
- Messleitungssatz der Zellspannung beschädigt · Fachwerkstatt
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P0DE6.