P02F1: Injecteur du cylindre 4 — circuit, plage/performance
Que faire
Ask for a voltage drop test on the injector wiring rather than just a continuity check. They are not the same thing — a circuit can show perfect continuity and still lose too much voltage when it actually carries current, and that is the commonest cause of this fault on the last cylinder of the harness.
Ask for the connector at the module end to be checked too, not only the one at the injector. Everything in that run adds up.
Expect rough running and possibly reduced power.
Get it repaired reasonably promptly. A cylinder that is not firing correctly sends unburnt fuel into the exhaust, and that can damage the catalytic converter or particulate filter — a far larger bill than the fault itself.
Ce que signifie ce code
The electrical behaviour of cylinder 4's injector circuit is wrong, without being open or short.
The module drives the injector and reads the current waveform back; cylinder 4's is valid but not the shape a healthy injector produces.
On a four-cylinder engine this is the last cylinder, and it is usually the far end of the injector harness — which gives it the family's most ordinary cause. Every connection between the module and this injector is in series with it, so it accumulates whatever resistance the whole run has picked up: the module connector, any intermediate joint, the loom branch, and its own plug.
A voltage drop test along that run finds this quickly, and a continuity test does not. Continuity confirms a path exists; it says nothing about how much voltage that path loses when real current flows, and injector drive current is substantial. That distinction is the whole test.
This is the same failure mode as a corroded battery terminal that cranks fine until it is cold. The circuit works until it is asked to carry current.
Where the wiring is sound, the injector itself is the answer — a degraded winding or piezo stack genuinely changes the electrical characteristic, and on a high-mileage engine that is an honest outcome rather than a last resort.
Check for an injector control module if the engine has one, since a failing drive stage there produces this on the cylinder it serves.
Causes probables
Commencez ici
- Connecteur corrodé ou mal enclenché · facile
- Injecteur de carburant hors service · spécialisée
Moins fréquent
- Faisceau de câblage endommagé · modérée
- Circuit ouvert dans le câblage de l'injecteur · modérée
Rare
- Calculateur de commande d'injecteurs hors service · spécialisée
Symptômes
Composants concernés
Des informations, pas des instructions
CarGeek est un ouvrage de référence, pas un manuel d'atelier. Ses pages sont rédigées à partir de sources publiques et de ce que d'autres ont constaté, jamais à partir de la documentation technique du constructeur ; elles peuvent donc être erronées ou incomplètes pour votre véhicule précis. Une partie de ce qu'elles décrivent présente un risque réel : haute tension, carburant sous pression, énergie accumulée, pièces chaudes ou en mouvement.
Avant d'agir sur quoi que ce soit, faites-le vérifier par une personne formée, en suivant la procédure du constructeur pour votre véhicule. Rien ici ne remplace cette procédure.
Expérience de la communauté
Soyez le premier à en faire le compte rendu
Rien n'a encore été publié à ce sujet. Tout ce que vous avez trouvé mérite d'être noté — même une impasse épargne à quelqu'un le même après-midi.
Ce qui rend un compte rendu utile :
- La voiture — marque, modèle, année et moteur. La même panne ne se comporte pas pareil sur chacune.
- Ce que vous avez mesuré, pas seulement ce que vous avez remplacé.
- Ce qui a réellement résolu le problème — ou que rien ne l’a résolu, ce qui est utile aussi.
Se connecter ou créer un compte pour ajouter ce que vous avez trouvé à propos de P02F1.