P02F1: Einspritzventil von Zylinder 4 — Stromkreis, Bereich/Funktion
Was zu tun ist
Ask for a voltage drop test on the injector wiring rather than just a continuity check. They are not the same thing — a circuit can show perfect continuity and still lose too much voltage when it actually carries current, and that is the commonest cause of this fault on the last cylinder of the harness.
Ask for the connector at the module end to be checked too, not only the one at the injector. Everything in that run adds up.
Expect rough running and possibly reduced power.
Get it repaired reasonably promptly. A cylinder that is not firing correctly sends unburnt fuel into the exhaust, and that can damage the catalytic converter or particulate filter — a far larger bill than the fault itself.
Was dieser Code bedeutet
The electrical behaviour of cylinder 4's injector circuit is wrong, without being open or short.
The module drives the injector and reads the current waveform back; cylinder 4's is valid but not the shape a healthy injector produces.
On a four-cylinder engine this is the last cylinder, and it is usually the far end of the injector harness — which gives it the family's most ordinary cause. Every connection between the module and this injector is in series with it, so it accumulates whatever resistance the whole run has picked up: the module connector, any intermediate joint, the loom branch, and its own plug.
A voltage drop test along that run finds this quickly, and a continuity test does not. Continuity confirms a path exists; it says nothing about how much voltage that path loses when real current flows, and injector drive current is substantial. That distinction is the whole test.
This is the same failure mode as a corroded battery terminal that cranks fine until it is cold. The circuit works until it is asked to carry current.
Where the wiring is sound, the injector itself is the answer — a degraded winding or piezo stack genuinely changes the electrical characteristic, and on a high-mileage engine that is an honest outcome rather than a last resort.
Check for an injector control module if the engine has one, since a failing drive stage there produces this on the cylinder it serves.
Wahrscheinliche Ursachen
Hier anfangen
- Korrodierter oder loser Stecker · einfach
- Einspritzventil ausgefallen · Fachwerkstatt
Seltener
- Kabelbaum beschädigt · mittel
- Leitungsbruch in der Injektorleitung · mittel
Selten
- Steuergerät der Einspritzventile ausgefallen · Fachwerkstatt
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P02F1.