U0311: Software-incompatibiliteit met de regelmodule aandrijfmotor
Wat te doen
Do not attempt anything under the bonnet, and have the vehicle recovered rather than persisting with it. The high-voltage system runs at several hundred volts and is not something to investigate.
Expect the car not to move at all, or to run on the engine alone if it has one.
That is the car doing the right thing, and it is worth understanding why. This code means two computers are running software that does not agree about what a torque request means. Rather than risk acting on a command it might interpret at the wrong scale — or in the wrong direction — the drive system commands no torque at all and shuts the high-voltage system down.
On a car whose motor can deliver full torque from a standstill, that is a far better answer than the alternatives. Nothing is broken.
One question worth asking yourself: has the car updated its software recently, or been part-way through an update? These systems are updated over the air more than almost anything else on a modern vehicle, and an update that only partly completed is a leading cause. If so, the fix is completing it rather than replacing anything.
Make sure it goes to a workshop equipped for high-voltage work, and tell the recovery operator what the vehicle is when you call.
Wat deze code betekent
A module is running software that does not belong with the drive motor control module's. See U0300 for the family, and note that everything on this page concerns a high-voltage system that is lethal in a way nothing mechanical on a vehicle is — several hundred volts of direct current, orange cabling that is not decorative, and no part of it that a general workshop should open.
A drive motor control module is the interface between a torque request and an inverter that turns hundreds of volts into three precisely timed phases. What a given request means — its scale, its sign, the current limits that bound it, the rotor position offset that keeps the phases aligned to the magnets — is all defined in software.
Which is why the vehicle's response to a mismatch here is not graceful degradation. A drive system that cannot be certain both halves agree about torque commands the safest available value, which is none, and opens the contactors. Expect a vehicle that will not move, or that moves on the engine alone if it has one.
And that is the correct outcome rather than an inconvenience. The failure this prevents is a torque command interpreted at the wrong scale or the wrong sign — a motor delivering far more than was asked for, or driving against the direction of travel. On a vehicle whose motor can produce full torque from rest, neither is survivable to get wrong, and refusing to move is a much better answer than either.
So the practical advice is to have it recovered rather than to persist, and to send it to a workshop equipped for high-voltage work.
Where it comes from is the family's ordinary list, with one addition specific to electric drive. Motor and inverter software is updated more often than almost anything else on these vehicles, frequently over the air, so a partly-completed update is a leading cause — and the remedy is completing it rather than replacing anything.
Waarschijnlijke oorzaken
Begin hier
- Software slechts op één module bijgewerkt · specialistisch
- Programmeren van de module onderbroken · specialistisch
- Verkeerde configuratie van de module na vervanging · specialistisch
Minder vaak
- Tweedehands module vergrendeld op een ander voertuig · specialistisch
- Softwarekalibratie verouderd · specialistisch
- Module niet gecodeerd op het voertuig · specialistisch
Symptomen
Betrokken onderdelen
Informatie, geen instructie
CarGeek is een naslagwerk, geen werkplaatshandboek. De pagina's zijn geschreven op basis van openbare bronnen en van wat anderen hebben ondervonden, nooit op basis van de servicedocumentatie van de fabrikant zelf, dus ze kunnen onjuist of onvolledig zijn voor jouw specifieke voertuig. Een deel van wat erin staat brengt echt gevaar met zich mee: hoogspanning, brandstof onder druk, opgeslagen energie en hete of bewegende delen.
Laat alles waarnaar je wilt handelen eerst controleren door iemand met een technische opleiding, aan de hand van de eigen procedure van de fabrikant voor jouw voertuig. Niets hier vervangt die procedure.
Ervaring uit de community
Wees de eerste die dit beschrijft
Hierover is nog niets geplaatst. Wat je ook hebt gevonden, het is het opschrijven waard — zelfs een doodlopend spoor bespaart iemand dezelfde middag.
Wat het de moeite waard maakt:
- De auto — merk, model, bouwjaar en motor. Dezelfde storing gedraagt zich per auto anders.
- Wat je gemeten hebt, niet alleen wat je vervangen hebt.
- Wat het echt verholpen heeft — of dat niets dat deed, wat ook nuttig is om te weten.
Inloggen of een account aanmaken om toe te voegen wat je hebt gevonden over U0311.