P2414: Lambdasonde — Fehler der Abgasprobe, Bank 1 Sensor 1
Was zu tun ist
Expect worse economy and possibly a rough idle. This code says the exhaust reaching the sensor is not representative, which usually means a leak in the exhaust ahead of it rather than a failed sensor — so ask for the exhaust and the sensor's fitment to be inspected before a part is bought. If a spacer or anti-fouling adapter has been fitted to the sensor at any point, mention it: those change what the sensor sees and are a direct cause of this.
Was dieser Code bedeutet
The upstream sensor on bank 1 is not receiving a representative sample of exhaust gas. The wording is precise and worth reading carefully: this code is about the sample, not about the sensor.
A sensor can be electrically perfect and chemically healthy and still report nonsense if what reaches it is not what left the cylinders. The ways that happens are physical and mostly visible:
- An exhaust leak upstream of it, drawing outside air in on each pressure pulse and diluting the sample. The corpus meets this repeatedly, and it belongs at the top of the list here too.
- The sensor not fully seated, or its threads not sealing, which lets air in at the sensor itself.
- A damaged or missing protective shield — the perforated tip that controls how gas flows across the element. Its geometry is part of the design, and a sensor fitted without it, or with it crushed, samples differently.
- An anti-fouling spacer fitted deliberately. These move the sensor out of the gas stream, and they exist largely to suppress catalyst efficiency codes. This code is one of the ways that shows up, and it is worth naming plainly: a spacer fitted to quieten P0420 is masking a fault rather than fixing one.
- A sensor of the wrong part number whose tip sits at a different depth.
So the diagnosis is a physical inspection of the exhaust and the installation before anything electrical, and this is one of the few oxygen sensor codes where a new sensor is unlikely to be the answer.
Wahrscheinliche Ursachen
Hier anfangen
- Abgasleck vor der Sonde · mittel
- Lambdasonde nicht korrekt eingeschraubt · einfach
Seltener
- Sensorabschirmung beschädigt oder fehlt · mittel
- Abstandshalter gegen Verrußung an der Sonde montiert · einfach
- Falsche Lambdasonde eingebaut · mittel
- Defekte Lambdasonde · mittel
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P2414.