U0406: Dados inválidos recebidos do módulo de controle dos injetores
O que fazer
Expect reduced power and possibly a limited rev range, along with rough running.
This module drives the injectors and reports back whether each injection actually happened as asked. When that report stops making sense, the engine deliberately holds back rather than fuelling on information it cannot verify — so the lack of power is protection.
The fault is often a single injector rather than the module. These modules report on each injector separately, and one shorted or open injector is enough to make the whole report unacceptable. Ask for the injectors and their wiring to be tested individually before the module is replaced.
Two other things worth raising. If injectors have been replaced recently, ask whether their calibration codes were programmed — see P2690, because uncoded injectors produce feedback that does not add up. And ask for the module's mounting and heat sink to be checked: these run hot, and unlike most modules on the car, heat damage is a genuine cause here.
O que este código significa
The fuel injector control module is broadcasting data that cannot be accepted as true. See U0400 for the family's framing.
A separate injector control module exists where the injectors need drive electronics the engine module cannot provide directly — most commonly on diesels with piezo injectors, which require high voltages and precisely shaped pulses, and on some engines with hydraulically actuated injection.
What it reports back is the substance of this code: confirmation that each injection actually happened as commanded — the timing achieved, the current delivered, and whether any channel faulted. The engine module needs that feedback because it is fuelling on the assumption that its commands were carried out.
An implausible report therefore breaks a loop that matters. The engine module cannot verify what was injected, and its response is to derate — reduced power, sometimes a limited rev range — because continuing to fuel confidently on unverified feedback is the thing it must not do.
As with the rest of this family, look past the module. Injector control modules report per-channel results, and a single shorted or open injector is enough to make the whole report unacceptable — which the corpus already describes as one injector dragging a driver down. So the fault is frequently one injector or its wiring, not the module.
One thing specific to these systems and worth asking about: heat. These modules dissipate real power and are often mounted on the engine or in the engine bay with a heat sink. A module that has been cooking gradually is a genuine failure mode here — unlike most of the modules in this family — so its mounting, its heat sink contact and any thermal paste are worth inspecting rather than assumed.
And the calibration point from P2690 applies: injectors carry individual codes, and a set fitted without them produces feedback the module cannot reconcile.
Causas prováveis
Comece aqui
- Injetor em curto derrubando o estágio de saída · moderado
- Módulo de comando dos injetores inoperante · especializado
- Chicote dos injetores danificado · moderado
- Dano térmico ao sensor ou à fiação · moderado
- Conector corroído ou frouxo · fácil
Menos comum
- Injetor instalado sem inserir seu código de calibração · especializado
Sintomas
Componentes envolvidos
Informação, não instrução
O CarGeek é uma referência, não um manual de serviço. Suas páginas são escritas a partir de fontes públicas e do que outras pessoas constataram, nunca a partir da documentação de serviço do fabricante, de modo que podem estar erradas ou incompletas para o seu veículo específico. Parte do que descrevem envolve risco real: alta tensão, combustível sob pressão, energia acumulada e peças quentes ou em movimento.
Antes de agir com base em qualquer orientação, peça a verificação de uma pessoa com formação técnica, seguindo o procedimento do próprio fabricante para o seu veículo. Nada aqui substitui esse procedimento.
Experiência da comunidade
Seja o primeiro a documentar isto
Ainda não há publicações sobre isto. Vale a pena anotar tudo o que você descobriu — até um beco sem saída poupa a mesma tarde de outra pessoa.
O que faz valer a leitura:
- O carro — marca, modelo, ano e motor. A mesma falha se comporta de forma diferente em cada um.
- O que você mediu, não só o que trocou.
- O que realmente resolveu — ou que nada resolveu, o que também vale saber.
Entrar ou criar uma conta para adicionar o que você descobriu sobre U0406.