P00D2: Heizung der Lambdasonde — Steuerstromkreis, Bereich/Funktion, Bank 1 Sensor 2
Was zu tun ist
Ask whether other faults from the same oxygen sensor are stored. The heater is what brings the sensor up to working temperature, so a heater fault makes the sensor report nonsense too — and one repair usually clears both.
Ask for the connector to be inspected for heat damage. This circuit carries real current, so a failing connection burns rather than just corroding, and the discolouration is usually visible.
Have the battery and charging system checked if that has not been done recently, since a weak supply slows the heater enough to fail the test with nothing wrong.
The car will drive normally. This is an emissions monitoring fault, so plan the repair around your MOT rather than treating it as urgent.
Was dieser Code bedeutet
The heater circuit for the downstream oxygen sensor on bank 1 is behaving oddly without being open or shorted.
An oxygen sensor's heater is a precondition rather than a convenience, and knowing that explains why a heater fault sets sensor codes. A zirconia element produces no usable signal below roughly 300°C, so until the heater has done its work the sensor is simply not reporting.
Range/performance means the module is watching how the heater behaves and finding it wrong — usually by measuring the current it draws, from which the element's resistance and therefore its temperature can be inferred. The circuit conducts; it does not conduct correctly.
Which points at three things:
- Resistance in the circuit. A heater draws real current, so a corroded terminal both drops voltage and heats itself — which oxidises it further. Look for discoloured connector plastic, not just continuity.
- A degrading heater element, whose resistance has drifted with age so the module can no longer predict its temperature.
- Supply quality. A weak battery or poor earth slows warm-up enough to fail the test with a sound heater.
Expect sensor response or closed-loop codes stored alongside, and treat the heater as the cause. A sensor that never gets hot cannot report properly, so fixing the heater usually clears several codes at once.
On the downstream sensor the practical consequence is emissions monitoring rather than driveability — the car drives normally and cannot complete its self-checks.
Wahrscheinliche Ursachen
Hier anfangen
- Sondenheizung defekt · mittel
- Hoher Widerstand in der Sensorleitung · mittel
- Korrodierter oder loser Stecker · einfach
Seltener
- Zu niedrige Systemspannung · einfach
- Sicherung des Heizkreises durchgebrannt · einfach
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P00D2.