P01CB: Zylinder 1 — Funktion des Einspritzzeitpunkts, zu weit nach spät
Was zu tun ist
Say whether the engine is rougher from cold and improves as it warms up. That is the most useful single observation for this fault — worse cold points at compression or a glow plug on that cylinder, while a problem that is the same hot or cold points at the injector. Those are very different repairs.
Mention any glow plug warning or hard starting in cold weather, which supports the first of those.
Mention any recent injector work and whether calibration codes were programmed in, since an injector fitted without its code produces timing faults with a good part.
Expect worse fuel economy while it is unrepaired, because late combustion pushes heat out of the exhaust instead of into the crankshaft.
Was dieser Code bedeutet
Combustion on cylinder 1 is happening later than the module commanded.
This family adds a direction to the per-cylinder timing codes, and the direction is genuinely diagnostic — over-retarded and over-advanced have different causes and should be read differently.
Over retarded means the burn is late. Three mechanisms produce it:
- The injector opens late. A solenoid or piezo stack that has slowed with age or resistance takes longer to lift the needle after the command arrives. This is the commonest cause and it is specific to this cylinder.
- The fuel takes longer to ignite once injected. That is ignition delay, and it is driven by compression, glow plug performance and fuel cetane. A cylinder with low compression burns late for entirely mechanical reasons.
- Rail pressure is low, so the injected spray atomises more coarsely and takes longer to light.
Distinguishing them is easier than it sounds. An injector that opens late does so at all temperatures. A cylinder that burns late through poor compression or a dead glow plug is dramatically worse cold and improves as the engine warms.
So ask whether the fault is worse from cold. Worse cold and better warm points at compression or glow plug; consistent regardless of temperature points at the injector.
Late combustion wastes energy into the exhaust rather than the crank, so expect poor economy and higher exhaust temperatures.
Wahrscheinliche Ursachen
Hier anfangen
- Einspritzventil ausgefallen · Fachwerkstatt
Seltener
- Geringe Motorkompression · Fachwerkstatt
- Glühkerze ausgefallen · mittel
- Zu geringer Kraftstoffdruck · mittel
- Verunreinigter oder minderwertiger Kraftstoff · mittel
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P01CB.