P24D1: Regeneration des Partikelsensors nicht abgeschlossen
Was zu tun ist
This is the sensor cleaning itself, not the particulate filter regenerating — a much smaller thing, and it is worth being clear about because the two get confused. Driving differently will not fix this one.
Ask whether a heater fault from the same sensor is stored, since that is the usual cause and one repair normally clears several codes together.
Have the battery and charging system checked if they have not been recently. The cleaning cycle draws real current, and a tired battery or a poor earth can stop it completing on an otherwise healthy sensor.
The car will drive normally. Allow time before an MOT, because the emissions self-checks will not complete while this is stored.
Was dieser Code bedeutet
The particulate matter sensor's self-cleaning cycle did not finish.
Note carefully which regeneration this is about. It is not the particulate filter's regeneration — it is the sensor's own, much smaller one. The sensor burns the soot off its electrodes with a built-in heater so it can start a fresh measurement, and this code says that burn was started and not completed.
The distinction matters because the two faults get confused constantly, and the repairs have nothing in common. A filter regeneration is about driving conditions and a filter full of soot; this is about a heater on a small sensor.
Three explanations cover almost all of these.
- The heater is weak or failing, so the electrodes never reach burn-off temperature. Look for a heater resistance or heater circuit code alongside.
- The supply voltage sagged during the burn, which needs meaningful current — a tired battery or a poor earth does it.
- The cycle was interrupted by the engine being switched off partway through, which is benign if occasional.
A sensor that cannot clean itself is a sensor that cannot measure again. Its electrodes stay bridged with conductive soot, so it reports a permanently high reading that means nothing — and that downstream nonsense often sets the codes people notice first.
Fix the heater and the rest of the family usually clears with it.
Wahrscheinliche Ursachen
Hier anfangen
- Partikelsensor defekt · mittel
- Korrodierter oder loser Stecker · einfach
Seltener
- Zu niedrige Systemspannung · einfach
- Hoher Widerstand in der Sensorleitung · mittel
- Schlechte Masseverbindung des Sensors · mittel
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P24D1.