P0D6E: Tensão A do motor do compressor do ar-condicionado — alto
O que fazer
No air conditioning, and no cabin heating on a heat-pump car. The car will drive normally otherwise.
O que este código significa
The supply voltage at the electric air conditioning compressor's motor is above its upper limit.
The instrument-versus-reading distinction at P0D6D applies here too, in the other direction.
A genuinely high supply is rarer than a low one, because the pack's voltage is what it is. So this is more often the sensor reading high than the voltage being high — but it must be checked rather than assumed, since a real over-voltage on the compressor's supply would damage its inverter.
An electric car's air conditioning compressor is a high-voltage machine, and almost everything that follows from that surprises people who know conventional systems.
A belt-driven compressor stops when the engine stops. That is tolerable on a petrol car because the engine only stops when the car does. On a hybrid the engine stops at every set of lights, and on an electric car there is no engine at all — so the compressor has to be driven by its own motor, fed from the traction pack at several hundred volts, with its own inverter to turn that direct current into the three-phase supply the motor needs. That inverter is why this block has phase current codes for an air conditioning part.
Two consequences change what a fault here means. First, on many cars this same compressor cools the battery, so an air conditioning failure becomes a charging and power failure in warm weather — the driver reports a hot cabin and the car quietly reports reduced rapid-charging. Second, a heat pump runs this compressor in reverse to heat the cabin, so on a car with one, losing the compressor loses the heating too, in winter, when nobody suspects air conditioning.
And the repair carries a hazard that has no equivalent on a conventional system: the oil. A high-voltage compressor is lubricated by a specific non-conductive polyolester oil carried in the refrigerant. The PAG oil used in every belt-driven system absorbs moisture and conducts — put it into a high-voltage compressor and it degrades the motor's insulation, which can energise the refrigerant circuit and the metal pipework running through the car. This is a real and repeated workshop error, not a theoretical one, and it is the reason these systems must be serviced with dedicated equipment that has never seen PAG oil.
Causas prováveis
Comece aqui
- Conector corroído ou frouxo · especializado
- Compressor elétrico do ar-condicionado com defeito · especializado
Menos comum
- Chicote elétrico danificado · especializado
- Alimentação de tensão de referência do sensor inoperante · especializado
Rara
- Sobretensão no sistema de carga · especializado
Sintomas
Componentes envolvidos
Informação, não instrução
O CarGeek é uma referência, não um manual de serviço. Suas páginas são escritas a partir de fontes públicas e do que outras pessoas constataram, nunca a partir da documentação de serviço do fabricante, de modo que podem estar erradas ou incompletas para o seu veículo específico. Parte do que descrevem envolve risco real: alta tensão, combustível sob pressão, energia acumulada e peças quentes ou em movimento.
Antes de agir com base em qualquer orientação, peça a verificação de uma pessoa com formação técnica, seguindo o procedimento do próprio fabricante para o seu veículo. Nada aqui substitui esse procedimento.
Experiência da comunidade
Seja o primeiro a documentar isto
Ainda não há publicações sobre isto. Vale a pena anotar tudo o que você descobriu — até um beco sem saída poupa a mesma tarde de outra pessoa.
O que faz valer a leitura:
- O carro — marca, modelo, ano e motor. A mesma falha se comporta de forma diferente em cada um.
- O que você mediu, não só o que trocou.
- O que realmente resolveu — ou que nada resolveu, o que também vale saber.
Entrar ou criar uma conta para adicionar o que você descobriu sobre P0D6E.