P0D6D: Tensão A do motor do compressor do ar-condicionado — baixo
O que fazer
No air conditioning, and no cabin heating on a heat-pump car. The car will drive. This is a high-voltage supply fault rather than a compressor fault, so a replacement compressor would not fix it.
O que este código significa
The supply voltage at the electric air conditioning compressor's motor is below its lower limit.
This is a reading, not an instrument, and the corpus draws that line everywhere. P0D68 says the sensor's circuit is faulty. This one says the sensor is working and the voltage really is low — which points away from the compressor and back up its supply: the high-voltage fuse feeding it, the cable, the connection, or a pack that is itself sagging under load.
An electric car's air conditioning compressor is a high-voltage machine, and almost everything that follows from that surprises people who know conventional systems.
A belt-driven compressor stops when the engine stops. That is tolerable on a petrol car because the engine only stops when the car does. On a hybrid the engine stops at every set of lights, and on an electric car there is no engine at all — so the compressor has to be driven by its own motor, fed from the traction pack at several hundred volts, with its own inverter to turn that direct current into the three-phase supply the motor needs. That inverter is why this block has phase current codes for an air conditioning part.
Two consequences change what a fault here means. First, on many cars this same compressor cools the battery, so an air conditioning failure becomes a charging and power failure in warm weather — the driver reports a hot cabin and the car quietly reports reduced rapid-charging. Second, a heat pump runs this compressor in reverse to heat the cabin, so on a car with one, losing the compressor loses the heating too, in winter, when nobody suspects air conditioning.
And the repair carries a hazard that has no equivalent on a conventional system: the oil. A high-voltage compressor is lubricated by a specific non-conductive polyolester oil carried in the refrigerant. The PAG oil used in every belt-driven system absorbs moisture and conducts — put it into a high-voltage compressor and it degrades the motor's insulation, which can energise the refrigerant circuit and the metal pipework running through the car. This is a real and repeated workshop error, not a theoretical one, and it is the reason these systems must be serviced with dedicated equipment that has never seen PAG oil.
Causas prováveis
Comece aqui
- Conector corroído ou frouxo · especializado
- Fusível queimado ou alimentação inoperante · especializado
- Chicote elétrico danificado · especializado
Menos comum
- Compressor elétrico do ar-condicionado com defeito · especializado
- Isolamento do cabo de alta tensão danificado · especializado
Sintomas
Componentes envolvidos
Informação, não instrução
O CarGeek é uma referência, não um manual de serviço. Suas páginas são escritas a partir de fontes públicas e do que outras pessoas constataram, nunca a partir da documentação de serviço do fabricante, de modo que podem estar erradas ou incompletas para o seu veículo específico. Parte do que descrevem envolve risco real: alta tensão, combustível sob pressão, energia acumulada e peças quentes ou em movimento.
Antes de agir com base em qualquer orientação, peça a verificação de uma pessoa com formação técnica, seguindo o procedimento do próprio fabricante para o seu veículo. Nada aqui substitui esse procedimento.
Experiência da comunidade
Seja o primeiro a documentar isto
Ainda não há publicações sobre isto. Vale a pena anotar tudo o que você descobriu — até um beco sem saída poupa a mesma tarde de outra pessoa.
O que faz valer a leitura:
- O carro — marca, modelo, ano e motor. A mesma falha se comporta de forma diferente em cada um.
- O que você mediu, não só o que trocou.
- O que realmente resolveu — ou que nada resolveu, o que também vale saber.
Entrar ou criar uma conta para adicionar o que você descobriu sobre P0D6D.