U0176: Perda de comunicação com o sensor G do sistema de retenção
O que fazer
The airbag warning light means the crash protection may not work properly.
This one usually comes down to a plug rather than a sensor, and there is one thing worth insisting on when it is found.
These connectors are sealed with a rubber gasket and a locking clip, and both harden with age. Once the seal goes, moisture gets in and the pins corrode — green or bluish deposit on the metal, or a white powdery bloom. The circuit these sensors run on is extremely sensitive to that.
If a corroded connector is found, ask for it to be replaced rather than cleaned up. Cleaning it works for a while — long enough for the light to go out and the car to be handed back — and then it comes back, because the seal that let the water in is still not sealing. On most circuits cleaning is a fair economy; on an airbag circuit it is not.
Two things worth mentioning if they apply. Has the engine bay or the underside been pressure washed? That drives water past a tired seal in a way rain does not. And has the car stood unused for months? A car that is driven regularly warms its connectors and dries them out; one that sits does not.
Do not have the light cleared, and refuse a resistor in place of a sensor.
O que este código significa
A restraints system sensor has stopped being heard from. See U0170 for the one-versus-several rule; U0477 covers the mounting, which matters when a sensor reads wrongly — this page is about the connector, which is what matters when one goes quiet.
A crash sensor connector at the front or underside of a vehicle is sealed with a moulded gasket and a positive lock, and both age. The gasket hardens with heat cycling and stops sealing; the lock's plastic becomes brittle and stops holding the halves fully together. Neither shows from outside.
What follows is corrosion, and it has a recognisable appearance worth describing because it is diagnostic. Green or blue-green deposit on copper alloy pins, or a white powdery bloom on tinned ones. Either means moisture has been present for a long time, and a circuit that measures in the tens of milliohms cannot tolerate it.
The instruction that follows is firmer than it would be anywhere else on the vehicle: a corroded restraints connector is replaced, not cleaned. Cleaning restores continuity for a while — long enough for the lamp to go out and the vehicle to be handed back — and the corrosion resumes from where it was left, because the seal that let the water in is still not sealing. On any other circuit that is a defensible economy. On this one it is not.
Two contributory causes are worth naming because both are ordinary and neither is anyone's fault. Pressure washing an engine bay or a wheel arch drives water past a tired gasket in a way rain never does. And a vehicle that has stood unused for months loses the mild warming that normally drives moisture back out of a connector.
Causas prováveis
Comece aqui
- Conector corroído ou frouxo · fácil
- Infiltração de água no conector · moderado
- Chicote elétrico danificado · moderado
Menos comum
- Sensor de impacto deslocado durante reparo de funilaria · moderado
- Dano físico por detritos da via · moderado
- Módulo do sistema de retenção com defeito · especializado
Sintomas
Componentes envolvidos
Informação, não instrução
O CarGeek é uma referência, não um manual de serviço. Suas páginas são escritas a partir de fontes públicas e do que outras pessoas constataram, nunca a partir da documentação de serviço do fabricante, de modo que podem estar erradas ou incompletas para o seu veículo específico. Parte do que descrevem envolve risco real: alta tensão, combustível sob pressão, energia acumulada e peças quentes ou em movimento.
Antes de agir com base em qualquer orientação, peça a verificação de uma pessoa com formação técnica, seguindo o procedimento do próprio fabricante para o seu veículo. Nada aqui substitui esse procedimento.
Experiência da comunidade
Seja o primeiro a documentar isto
Ainda não há publicações sobre isto. Vale a pena anotar tudo o que você descobriu — até um beco sem saída poupa a mesma tarde de outra pessoa.
O que faz valer a leitura:
- O carro — marca, modelo, ano e motor. A mesma falha se comporta de forma diferente em cada um.
- O que você mediu, não só o que trocou.
- O que realmente resolveu — ou que nada resolveu, o que também vale saber.
Entrar ou criar uma conta para adicionar o que você descobriu sobre U0176.