P01CF: Zylinder 3 — Funktion des Einspritzzeitpunkts, zu weit nach spät
Was zu tun ist
Ask for a compression test on this cylinder before an injector is replaced, particularly if the car has high mileage. A new injector fitted to a cylinder with poor compression sets the same fault again within days — and that is the most common way this repair goes wrong.
Say whether the engine is much rougher from cold and settles as it warms up. That points at compression or a glow plug rather than the injector, and it is the cheapest thing to establish.
Mention any blue smoke, oil consumption, or a rattle from the engine, all of which support a mechanical rather than fuelling cause.
Expect worse fuel economy while it is unrepaired.
Was dieser Code bedeutet
Combustion on cylinder 3 is happening later than the module commanded.
Cylinder 3 sits in the hot middle of an inline block, which shapes both of the mechanical causes behind a late burn.
Heat bakes deposits onto the injector nozzle, narrowing the spray holes so the charge atomises coarsely and takes longer to light. And the centre cylinders are the ones whose bores and rings see the highest thermal load, so compression tends to fall there first on a worn engine. Both produce a late burn and both are worse on the cylinder this code names.
Separating them costs nothing and settles the repair.
- A compression test on that cylinder answers the mechanical question directly.
- A cold-start comparison answers it almost as well: low compression is dramatically worse cold and improves as the engine warms, because a warm cylinder seals better and the charge is already hot. A restricted injector behaves the same at any temperature.
Do not skip the compression test on a high-mileage engine just because an injector is the more convenient explanation. A new injector fitted into a cylinder with poor compression sets the same code within days, and that is the failure this code most often leads to.
Glow plug performance is the third candidate and it is cheap to check, though on a warm engine it will not explain a fault that persists.
Wahrscheinliche Ursachen
Hier anfangen
- Geringe Motorkompression · Fachwerkstatt
- Einspritzdüse verstopft oder eingeengt · Fachwerkstatt
- Einspritzventil ausgefallen · Fachwerkstatt
Seltener
- Glühkerze ausgefallen · mittel
- Zu geringer Kraftstoffdruck · mittel
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P01CF.