P2691: Daten des Einspritzventils von Zylinder 6 nicht kompatibel
Was zu tun ist
As at P2690 — if this followed injector work, nothing is broken and a calibration code has not been entered, or has been entered wrongly.
Expect uneven idle, a harder knock from one cylinder and some smoke until it is sorted.
One thing worth asking about specifically if your engine is a V6: was the cylinder numbering confirmed? Cylinder 6 is not necessarily the one at the end of a bank — the numbering follows the manufacturer's convention rather than the physical layout, and a code entered against the wrong cylinder puts two of them out at once rather than one.
Go back to whoever fitted the injectors and ask for the coding to be checked.
Was dieser Code bedeutet
The calibration data held for cylinder 6's injector does not match the injector fitted there, or is absent. What injector calibration codes are and why they must be entered per cylinder is explained in full at P2690.
On a six-cylinder engine this is the last cylinder, and that position makes one cause disproportionately likely: it is the one most often left until last and most often rushed. Injector replacement on an inline six means working progressively along the head, and the final injector is fitted when access is worst, the light is going and the job is nearly done. Both the fitting and the code entry are more error-prone at that point, which is why a single-cylinder coding fault on the last cylinder of a set is a recognisable pattern rather than a coincidence.
The other consideration specific to a six is bank identification. On a V6 the cylinder numbering is not the physical order along either bank, and cylinder 6 may sit anywhere depending on the manufacturer's convention. Entering a code against "the last injector fitted" rather than against the cylinder the module means is a straightforward way to get two cylinders wrong at once — so the numbering should be confirmed against the manufacturer's diagram, not inferred from the layout.
Wahrscheinliche Ursachen
Hier anfangen
- Injektor ohne Eingabe seines Kalibrierwerts eingebaut · Fachwerkstatt
- Kalibrierwert des Injektors falsch eingegeben · Fachwerkstatt
Seltener
- Injektoren zwischen den Zylindern vertauscht · Fachwerkstatt
- Motorsteuergerät getauscht oder programmiert · Fachwerkstatt
- Programmierung des Steuergeräts abgebrochen · Fachwerkstatt
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P2691.