P2778: Schalter für Hochschalten — Stromkreis sporadisch/unregelmäßig
Was zu tun ist
The car drives normally in D — what has failed is the manual shift request, not the gearbox. Leave the selector in drive and let it shift for itself until the circuit is repaired. Plan for long descents, because the usual answer — holding a low gear for engine braking — may not be available: slow down earlier and brake in shorter, firmer applications rather than dragging the brakes.
Was dieser Code bedeutet
The upshift switch signal is cutting in and out.
An intermittent signal is a connection fault until proven otherwise. A switch that has failed outright reads failed all day; a signal that comes and goes moves with vibration, temperature and steering angle — which points at a connector, a chafed run of harness, or a clock spring part-way through failing.
This is the request side of a manual shift, not the gearbox itself. On a car with a manual gate or steering-wheel paddles, pulling for a gear closes a switch, and the transmission control module reads that request and decides whether to honour it. This circuit is that switch's wiring.
The car still drives, because D never asks. Fully automatic shifting does not use the shift request circuits at all — the module schedules gears from speed and load on its own. What stops working is the manual override: the gearbox ignores the paddle or the gate, or drops back to automatic shortly after a request.
On a paddle car, the wiring runs through the steering wheel's clock spring — the wound ribbon cable that lets the wheel turn while staying connected. A clock spring worn out by years of steering, or disturbed by steering-wheel or airbag work, takes the paddles with it. If this code arrived soon after any work behind the wheel, start there — and take it seriously beyond the convenience, because the same ribbon usually carries the horn and airbag circuits.
The selector gate has its own failure mode: the switch contacts wear and corrode. A gate that only registers some pulls, or registers one pull twice, is a tired switch rather than a transmission fault — and a far cheaper repair than anything inside the gearbox.
Do not let this code send anyone into the transmission. Nothing here touches the hydraulics: the fluid, clutches and solenoids are all innocent until the request signal has been proven at the module connector.
Wahrscheinliche Ursachen
Hier anfangen
- Korrodierter oder loser Stecker · Fachwerkstatt
- Wählhebelschalter defekt · Fachwerkstatt
- Kabelbaum beschädigt · Fachwerkstatt
Seltener
- Wickelfeder im Lenkrad defekt · Fachwerkstatt
Selten
- Getriebesteuergerät defekt · Fachwerkstatt
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P2778.