P27E1: Elektrische oder Zusatz-Getriebeölpumpe A — Druck zu niedrig
Was zu tun ist
The car will drive normally — the usual sign is stop-start no longer switching the engine off. That is deliberate: the module will not stop the engine when it cannot hold hydraulic pressure through the stop. Have it repaired rather than living with it, because on hybrids the same pump covers engine-off driving, and a shunt on every restart is wear the clutches were never designed to absorb.
Was dieser Code bedeutet
Electric auxiliary transmission fluid pump A is running but its pressure is too low.
This is the outcome code: the pump was commanded, it ran, and the pressure still did not arrive. The control circuit tests clean — what failed is the hydraulic result. That distinction matters, because it moves suspicion from the wiring to the pump's ability to actually move fluid.
Three things stop a running pump from making pressure. Worn pump elements let fluid slip back past them instead of being pushed forward; an internal leak — a tired seal, a perished O-ring — bleeds off what is built before it reaches the circuit; and fluid that is low, aerated or degraded gives the pump less to work with in the first place. The fluid check costs nothing and comes first.
This pump exists for the moments the engine is off. A conventional automatic makes its hydraulic pressure with a pump driven by the engine, so at a stop-start red light — engine stopped — pressure would drain away, and the first metre of drive would arrive with a thump while the mechanical pump refilled the circuit. The electric auxiliary pump holds pressure through those stops, so the clutches are already applied when the engine restarts. Hybrids lean on it even harder, because their engine stops whenever the battery can carry the load.
Which is why the commonest symptom is no symptom at all — except stop-start quietly giving up. The module knows it cannot hold pressure through an engine stop, so it stops allowing them. A car that used to switch off at the lights and no longer does, with this code stored, has already told you what is wrong. Where stops do still happen, the tell is a pause or a shunt as the car pulls away afterwards.
Wahrscheinliche Ursachen
Hier anfangen
- Zusatzpumpe für Getriebeöl defekt · Fachwerkstatt
- Getriebeöl zu wenig oder verbraucht · mittel
Seltener
- Dichtung oder O-Ring porös · Fachwerkstatt
- Leckage im Hydrauliksystem · Fachwerkstatt
- Abrieb im Getriebeöl · Fachwerkstatt
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P27E1.