P27E4: Regelventil der Getriebeölpumpe — Stromkreis, Bereich/Funktion
Was zu tun ist
The car will drive normally — the usual sign is stop-start no longer switching the engine off. That is deliberate: the module will not stop the engine when it cannot hold hydraulic pressure through the stop. Have it repaired rather than living with it, because on hybrids the same pump covers engine-off driving, and a shunt on every restart is wear the clutches were never designed to absorb.
Was dieser Code bedeutet
The auxiliary transmission fluid pump control valve circuit is reading outside its expected range.
Range/performance means the signal is present but implausible — a voltage between valid states, a request pattern no driver could produce. That points at partial corrosion or a misadjusted switch rather than a clean break.
The control valve routes what the auxiliary pump makes. The pump feeds the transmission's main circuit through a valve that directs and holds its output where it is needed. When the valve's circuit fails, the pump can run perfectly and still achieve nothing — pressure goes unrouted, and the stop-start behaviour this system exists for degrades exactly as if the pump itself had failed.
Electrically this is an ordinary solenoid circuit, and it fails the ordinary ways: corroded connectors, chafed wiring, a winding gone open or shorted. The valve also lives in the valve body, so debris in ageing fluid can gum its movement while the electrical side tests perfectly.
This pump exists for the moments the engine is off. A conventional automatic makes its hydraulic pressure with a pump driven by the engine, so at a stop-start red light — engine stopped — pressure would drain away, and the first metre of drive would arrive with a thump while the mechanical pump refilled the circuit. The electric auxiliary pump holds pressure through those stops, so the clutches are already applied when the engine restarts. Hybrids lean on it even harder, because their engine stops whenever the battery can carry the load.
Which is why the commonest symptom is no symptom at all — except stop-start quietly giving up. The module knows it cannot hold pressure through an engine stop, so it stops allowing them. A car that used to switch off at the lights and no longer does, with this code stored, has already told you what is wrong. Where stops do still happen, the tell is a pause or a shunt as the car pulls away afterwards.
Wahrscheinliche Ursachen
Hier anfangen
- Korrodierter oder loser Stecker · Fachwerkstatt
- Kabelbaum beschädigt · Fachwerkstatt
Seltener
- Abrieb im Getriebeöl · Fachwerkstatt
- Schaltschieberkasten verschlissen · Fachwerkstatt
Selten
- Getriebesteuergerät defekt · Fachwerkstatt
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P27E4.