P27E1: Pompe à huile de boîte électrique ou auxiliaire A — pression trop basse
Que faire
The car will drive normally — the usual sign is stop-start no longer switching the engine off. That is deliberate: the module will not stop the engine when it cannot hold hydraulic pressure through the stop. Have it repaired rather than living with it, because on hybrids the same pump covers engine-off driving, and a shunt on every restart is wear the clutches were never designed to absorb.
Ce que signifie ce code
Electric auxiliary transmission fluid pump A is running but its pressure is too low.
This is the outcome code: the pump was commanded, it ran, and the pressure still did not arrive. The control circuit tests clean — what failed is the hydraulic result. That distinction matters, because it moves suspicion from the wiring to the pump's ability to actually move fluid.
Three things stop a running pump from making pressure. Worn pump elements let fluid slip back past them instead of being pushed forward; an internal leak — a tired seal, a perished O-ring — bleeds off what is built before it reaches the circuit; and fluid that is low, aerated or degraded gives the pump less to work with in the first place. The fluid check costs nothing and comes first.
This pump exists for the moments the engine is off. A conventional automatic makes its hydraulic pressure with a pump driven by the engine, so at a stop-start red light — engine stopped — pressure would drain away, and the first metre of drive would arrive with a thump while the mechanical pump refilled the circuit. The electric auxiliary pump holds pressure through those stops, so the clutches are already applied when the engine restarts. Hybrids lean on it even harder, because their engine stops whenever the battery can carry the load.
Which is why the commonest symptom is no symptom at all — except stop-start quietly giving up. The module knows it cannot hold pressure through an engine stop, so it stops allowing them. A car that used to switch off at the lights and no longer does, with this code stored, has already told you what is wrong. Where stops do still happen, the tell is a pause or a shunt as the car pulls away afterwards.
Causes probables
Commencez ici
- Pompe à huile de boîte auxiliaire défectueuse · spécialisée
- Huile de boîte insuffisante ou dégradée · modérée
Moins fréquent
- Joint ou joint torique craquelé · spécialisée
- Fuite du circuit hydraulique · spécialisée
- Débris dans l'huile de boîte de vitesses · spécialisée
Symptômes
Composants concernés
Des informations, pas des instructions
CarGeek est un ouvrage de référence, pas un manuel d'atelier. Ses pages sont rédigées à partir de sources publiques et de ce que d'autres ont constaté, jamais à partir de la documentation technique du constructeur ; elles peuvent donc être erronées ou incomplètes pour votre véhicule précis. Une partie de ce qu'elles décrivent présente un risque réel : haute tension, carburant sous pression, énergie accumulée, pièces chaudes ou en mouvement.
Avant d'agir sur quoi que ce soit, faites-le vérifier par une personne formée, en suivant la procédure du constructeur pour votre véhicule. Rien ici ne remplace cette procédure.
Expérience de la communauté
Soyez le premier à en faire le compte rendu
Rien n'a encore été publié à ce sujet. Tout ce que vous avez trouvé mérite d'être noté — même une impasse épargne à quelqu'un le même après-midi.
Ce qui rend un compte rendu utile :
- La voiture — marque, modèle, année et moteur. La même panne ne se comporte pas pareil sur chacune.
- Ce que vous avez mesuré, pas seulement ce que vous avez remplacé.
- Ce qui a réellement résolu le problème — ou que rien ne l’a résolu, ce qui est utile aussi.
Se connecter ou créer un compte pour ajouter ce que vous avez trouvé à propos de P27E1.