P016C: Gemischregelung im geschlossenen Regelkreis an der Grenze — Gemisch zu mager
Was zu tun ist
Say whether the problem is worse at idle or under acceleration — it is the single most useful thing you can report here. Worse at idle points at an air leak; worse under load points at fuel supply, and those are completely different repairs.
Mention any hissing or whistling from the engine bay, especially at idle, which suggests an air leak.
Say when the fuel filter was last changed, since a restricted filter is a common and inexpensive cause on the fuel side.
Do not leave it running lean for long. A lean mixture burns hotter and can damage the catalytic converter and, in the worst case, the engine itself.
Was dieser Code bedeutet
The module has added as much fuel as its closed loop authority permits and the mixture is still lean.
This code is the sound of a correction running out of room, which makes it more informative than an ordinary lean code. The module is not reporting that the mixture drifted — it is reporting that it tried to fix it, went to the end of its adjustment, and failed. The fault is therefore larger than trim can absorb.
Two families of cause, and separating them is the whole diagnosis.
Unmetered air entering after the airflow sensor. The module fuels for the air it measured; anything arriving later is unaccounted for and leans the mixture out. Split intake hoses, a perished PCV hose, a leaking intake manifold gasket, a loose dipstick tube or a failed brake servo hose all do it. A leak of this kind is usually worse at idle and improves under load, because manifold depression is highest at idle.
Fuel that is not arriving. A weak pump, a restricted filter, a failing pressure regulator or blocked injectors. This pattern is the reverse — worse under load and better at idle — because demand exposes a supply shortfall that light throttle does not.
That single question, 'is it worse at idle or under load?', separates the two halves before anything is dismantled. It is the most useful thing to establish here.
And check the measurement itself: a mass airflow sensor reading high makes the module fuel for air that was never there.
Wahrscheinliche Ursachen
Hier anfangen
- Falschluft hinter dem Luftmassenmesser · mittel
- Luftmassenmesser defekt · einfach
- Zu geringer Kraftstoffdruck · mittel
Seltener
- Einspritzdüse verstopft oder eingeengt · Fachwerkstatt
- Abgasleck stromaufwärts der Sonde · mittel
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P016C.