P01BA: Motoröltemperatursensor B — Bereich/Funktion
Was zu tun ist
Leaving the car overnight helps considerably. This kind of fault is found from stone cold, when every temperature sensor on the vehicle should agree with the others — a warm engine tells the garage much less.
Mention if the engine has been using oil, or if an oil change is overdue. Some vehicles calculate service intervals partly from oil temperature, so this fault can also distort the service indicator.
Ask for the connector and wiring to be checked before the sensor is replaced. Added resistance in the wiring shifts the reading in a way that looks exactly like a drifted sensor and is much cheaper to fix.
The car will usually drive normally, though on some engines it may hold back full power until it believes the oil is warm.
Was dieser Code bedeutet
The second engine oil temperature sensor is reporting a value that is electrically valid but does not fit the conditions.
Oil temperature is used for more than a gauge, which is why a drifted sensor matters more than it appears to. The module uses it to decide when variable valve timing may operate, since the phasers are driven by oil pressure and behave differently with cold, thick oil; when to allow full power, on engines that protect themselves until the oil is warm; and when the oil is due for a change on vehicles with a condition-based service indicator.
So a sensor reading falsely high can grant full power and full valve timing authority to an engine still running on cold oil — which is the consequence worth naming, because nothing warns the driver.
Range/performance is caught by the cold soak comparison, as with every temperature sensor. After the vehicle has stood overnight, oil, coolant and intake air should all read close to ambient and close to each other. The one that disagrees has identified itself.
A second oil temperature sensor implies a system that cares about oil at two points — commonly one in the sump and one in the gallery or cooler circuit. A genuine difference between them is not necessarily a fault, so confirm which sensor B is on this engine before assuming the two should read identically when running.
High resistance in the wiring is a frequent cause, and it shifts the reading consistently rather than erratically — which looks exactly like sensor drift until the connector is inspected.
Wahrscheinliche Ursachen
Hier anfangen
- Sensor aus der Kalibrierung gedriftet · mittel
- Hoher Widerstand in der Sensorleitung · mittel
- Korrodierter oder loser Stecker · einfach
Seltener
- Öl im Sensorstecker · einfach
Selten
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P01BA.