P020B: Zylinder 2 — Einspritzzeitpunkt
Was zu tun ist
Mention any recent injector work — and if only some injectors were replaced, say which. Diesel injectors carry a calibration code that must be programmed in when they are fitted, and one installed without that step sets exactly this fault.
Note whether the roughness is worse cold or hot, and whether it clears once the engine is warm. That single observation separates an injector problem from a compression or glow plug one on that cylinder.
Ask for the cylinder numbering to be confirmed against the manufacturer's diagram if a part is going to be replaced. It is not always the cylinder you would count to from the front, and on a V engine it is often on the other bank.
Was dieser Code bedeutet
Injection timing on cylinder 2 is not where the module commanded it to be.
The mechanism is the family's — the module reads each combustion event in the crankshaft's instantaneous speed and compares when the fuel burned against when it asked for it. What varies between members is which cylinder, and that is exactly the diagnostic information the code carries.
Cylinder numbering is where this goes wrong in practice, and it is worth being careful about. Cylinder 2 means the second cylinder in the manufacturer's firing order convention, which is not always the second one you reach from the front of the engine. On a V engine it is frequently on the opposite bank from where a mechanic's intuition puts it. Confirm the numbering against the manufacturer's own diagram before removing anything.
The wrong injector removed is not a harmless mistake on a modern diesel — the calibration code of whatever is disturbed has to be reprogrammed, and the original fault is still there afterwards.
Where cylinder 2 sits next to another cylinder that has also set a timing code, look for what the two share before treating them as separate faults: a common rail pressure sensor, one fuel supply line, or a return circuit feeding both.
Wahrscheinliche Ursachen
Hier anfangen
- Einspritzventil ausgefallen · Fachwerkstatt
- Injektor ohne Eingabe seines Kalibrierwerts eingebaut · Fachwerkstatt
- Einspritzventile verschlissen oder undicht · Fachwerkstatt
Seltener
- Geringe Motorkompression · Fachwerkstatt
- Injektoren zwischen den Zylindern vertauscht · Fachwerkstatt
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P020B.