P02CE: Zylinder 2 — Offsetanlernung von Einspritzventil A an der Untergrenze
Was zu tun ist
Ask whether the injector calibration codes match the cylinders they are actually fitted to. If injectors have been out for any reason, two of them swapped over produces exactly this kind of fault — and it is corrected with a laptop rather than with parts.
Check the engine oil level and smell it. Over-delivery washes diesel past the rings into the sump, and oil above maximum or smelling strongly of fuel is urgent rather than a curiosity.
Ask what the other cylinders' trims look like. If they are all drifting the same way the problem is shared — fuel pressure or fuel quality — and no injector needs replacing at all.
Do not delay. The module ran out of adjustment, so this has been developing quietly for some time.
Was dieser Code bedeutet
The correction the module applies to cylinder 2's injector has reached the bottom of its adjustment range.
The module trims each injector individually to equalise delivery, and this says cylinder 2's trim has run out at the bottom — it has been reduced as far as permitted and the cylinder is still delivering more than its share.
Where more than one cylinder shows an offset code, the pattern is more informative than any single one of them, and it is worth reading before anything is removed.
- One cylinder at a limit points at that injector.
- All cylinders drifting the same way points at something shared — rail pressure, the pressure sensor, or fuel quality. The injectors may be fine and the reference wrong.
- Two cylinders at opposite limits is the signature of injectors swapped between cylinders, where each is now running the other's calibration code. That is a coding fix rather than a parts job.
That third case is worth checking specifically after any injector work. It is easy to do, produces dramatic-looking codes, and costs nothing to correct once identified.
Over-delivery on one cylinder has its own consequence: unburnt fuel washes the cylinder wall and drains into the sump, so check the oil level and condition — a level that has risen, or oil that smells of diesel, is a genuine finding rather than an aside.
Wahrscheinliche Ursachen
Hier anfangen
- Injektoren zwischen den Zylindern vertauscht · Fachwerkstatt
- Injektor ohne Eingabe seines Kalibrierwerts eingebaut · Fachwerkstatt
- Einspritzventile verschlissen oder undicht · Fachwerkstatt
Seltener
- Einspritzventil ausgefallen · Fachwerkstatt
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P02CE.