P02CF: Zylinder 2 — Offsetanlernung von Einspritzventil A an der Obergrenze
Was zu tun ist
Say whether the engine is rough at idle but smooth once you are moving. That pattern is characteristic of this fault and genuinely helps confirm it.
Ask whether the injector calibration codes are right for the cylinders they are on. If another cylinder has an opposite fault stored, two injectors carrying each other's codes is a likely explanation — and that is a coding correction, not a parts bill.
Ask about fuel contamination and the age of the fuel filter, since debris or water narrows the injector's spray holes and produces exactly this.
Do not run it like this for months. A cylinder receiving less fuel than its neighbours runs hotter, and on a diesel that can damage the piston.
Was dieser Code bedeutet
The correction the module applies to cylinder 2's injector has reached the top of its adjustment range.
The module has been adding as much fuelling correction as it is permitted to on cylinder 2, and the cylinder is still under-delivering. The trim has run out and the shortfall remains.
Under-delivery on a single cylinder produces a specific and recognisable behaviour worth knowing, because it helps confirm the diagnosis before anything is dismantled. The engine is roughest at idle and light load, and smooths out under power. At idle the per-cylinder contribution is small and one weak cylinder is obvious; under load every cylinder is delivering far more and a fixed shortfall matters proportionally less.
A driver describing 'rough when stopped at lights, fine on the motorway' is describing this.
The causes are the under-delivery set: a restricted nozzle, a slow-opening solenoid or piezo stack, a wrong calibration code, or contamination that has narrowed the spray holes.
Where an engine has this on one cylinder and a minimum-limit code on another, suspect the calibration codes before suspecting the injectors. Two injectors carrying each other's codes push their trims to opposite limits, and nothing is mechanically wrong at all.
Prolonged under-delivery is not harmless. A cylinder that runs lean of its neighbours runs hotter, and on a diesel that is a route to piston and glow plug damage rather than merely a rough idle.
Wahrscheinliche Ursachen
Hier anfangen
- Einspritzdüse verstopft oder eingeengt · Fachwerkstatt
- Injektor ohne Eingabe seines Kalibrierwerts eingebaut · Fachwerkstatt
- Verunreinigter oder minderwertiger Kraftstoff · mittel
Seltener
- Injektoren zwischen den Zylindern vertauscht · Fachwerkstatt
- Einspritzventil ausgefallen · Fachwerkstatt
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P02CF.