P0C50: Positionssensor von Antriebsmotor A — Stromkreis A
Was zu tun ist
Losing one channel of a resolver loses the angle completely — the two channels are halves of one measurement, not a spare. Expect electric drive to be cut rather than reduced. Before a sensor is replaced, ask whether the wiring and its shielding were checked: these are low-level analogue signals and a resistive joint or a disturbed screen produces exactly this. Nothing here is a home job.
Was dieser Code bedeutet
Channel A of the position sensor on drive motor a has a circuit fault.
Two things need separating before this makes sense, and the corpus carries both.
First, this is not the same code as P0A3F. That one names the position sensor as a whole; these name its individual channels. The same shape as the current sensors at P0BE5 — a whole-thing code beside per-channel codes — and the same trap if they are read as duplicates.
Second, and this is the good part: channel A and channel B are not two sensors, and they are not redundant. A resolver reports rotor angle as two signals — one proportional to the sine of the angle, one to the cosine. Either alone is ambiguous: a sine value of one half is consistent with thirty degrees and with a hundred and fifty. Only the two together give a unique angle. So losing one channel does not degrade the measurement, it destroys it, and the inverter has no idea where the rotor is.
And the pair carries a self-check that costs nothing, which is the third time this block has used the trick. Sine squared plus cosine squared equals one, at every angle, always. So the module can verify its own position measurement against a mathematical identity — exactly as it sums the three phase currents to zero at P0BFD, and checks the planetary speed equation at P0C2F. When the sum of squares drifts away from one, something is wrong with a channel even though both signals still look like plausible waveforms.
That is what most Range/Performance faults in this family are: not a dead channel, but a channel whose amplitude has drifted, usually because a connection has gone resistive or shielding has been disturbed.
Wahrscheinliche Ursachen
Hier anfangen
- Positionssensor des Elektromotors defekt · Fachwerkstatt
- Korrodierter oder loser Stecker · einfach
Seltener
- Kabelbaum scheuert zwischen Getriebe und Wechselrichter · Fachwerkstatt
- Referenzspannungsversorgung des Sensors ausgefallen · mittel
- Positionssensor des Motors falsch eingebaut oder verdreht · Fachwerkstatt
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P0C50.