P24B9: Drucksensor der Leckerkennungspumpe des Kraftstoffverdunstungssystems — Stromkreis, Bereich/Funktion
Was zu tun ist
This is a low-urgency fault and the car will drive normally. It concerns the system that checks the fuel tank for vapour leaks, not anything that affects how the engine runs.
It matters at MOT time. While it is stored the vehicle cannot complete its evaporative emissions self-check, and an incomplete readiness monitor can fail the test on its own — so leave time before the MOT rather than booking it for the same week.
Mention if you can smell fuel at any point. That would suggest a genuine leak alongside the sensor fault, and it changes the priority considerably.
Keep the fuel filler cap tight and correctly seated. It is part of the sealed system this pump tests, and a loose or perished cap seal causes related faults.
Was dieser Code bedeutet
The pressure sensor inside the evaporative emission leak detection pump is reporting an implausible value.
This belongs to the fuel vapour system rather than the exhaust, despite sitting in a block of aftertreatment codes. Its job is to prove the fuel tank and its vapour lines do not leak — which the vehicle tests by pumping the system up or drawing it down and watching whether the pressure holds.
The sensor in question is the instrument for that test. So this code does not say the tank leaks; it says the equipment that checks for leaks cannot be trusted. No leak test can run while it is stored, which is why it blocks an emissions readiness monitor.
Range/performance means the reading is present but wrong. The classic evidence is a sensor not reading atmospheric pressure when the system is open to atmosphere and the engine has been off for hours — at that moment every pressure sensor in the vehicle should agree, and one that does not has declared itself.
The pump assembly is usually replaced complete, because the sensor is generally built into it rather than serviced separately.
Check the obvious first. The unit is mounted near the fuel tank or charcoal canister where road spray reaches it, and a blocked filter or a hose full of water produces this code with a working sensor.
Wahrscheinliche Ursachen
Hier anfangen
- Leckdiagnosepumpe des Tanksystems defekt · mittel
- Korrodierter oder loser Stecker · einfach
Seltener
- Filter des Tankentlüftungssystems verstopft · einfach
- Wasser in den Stecker eingedrungen · einfach
- Tankentlüftungsschlauch verstopft oder geknickt · einfach
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P24B9.