P2788: Adaptives Anlernen des manuellen Modus des Automatikgetriebes an der Grenze
Was zu tun ist
Drivable, but the message is about what comes next. If nothing has been replaced recently, the clutch is most likely near the end of its wear and the smoothness you still have is the software's last reserves — plan the repair rather than being surprised by it. If a clutch or actuator was just changed, ask for the calibration procedure before paying for anything else.
Was dieser Code bedeutet
Adaptive learning for the automated shift system has reached the end of its range.
The module learns the clutch the way your leg learns one. No two clutches bite at the same point or carry the same torque per millimetre of travel, and both drift as the material wears. So the module continuously measures where its clutch bites and how much it transmits, and updates a stored model — that adaptation is why a gearbox still shifts smoothly at 150,000 miles on a clutch half worn away.
At limit means the learning has run out of room. Adaptation absorbs change, but only within a window, and the stored values have reached its edge. The software can no longer compensate for what the hardware has become. A clutch worn to the end of its service life is the ordinary reason, and this code is often the first formal notice — arriving before slip, judder or smell make it obvious.
The other route here is a lost baseline rather than a worn part. Replace a clutch or an actuator and the learned values now describe a part that is no longer in the car; interrupt the wrong procedure and they are simply gone. A scan-tool teach-in re-baselines the system — so a gearbox that shifts badly immediately after clutch or actuator work needs calibration, not a second clutch.
This code straight after a repair is good news, relatively speaking: the fix is a procedure, not parts. The same code on an original clutch at high mileage means the opposite — budget for the clutch, and treat smooth shifting in the meantime as borrowed time.
Wahrscheinliche Ursachen
Hier anfangen
- Lamellenpakete verschlissen · Fachwerkstatt
- Steller nach Reparatur nicht kalibriert · mittel
Seltener
- Kalibrierung des Getriebestellers verloren · mittel
- Ölverschmutzung an der Kupplung · Fachwerkstatt
- Kupplungssteller defekt · Fachwerkstatt
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P2788.