Zum Inhalt springen

U0442 Hoch Generisch / SAE

U0442: Ungültige Daten vom Motorsteuergerät B empfangen

WhatsApp Telegram X E-Mail

Was zu tun ist

Expect reduced power, possibly a rough-running engine, and several warnings at once.

Some engines are managed by two computers rather than one — a large V engine may run one per bank, and some diesels split the work between two units. They constantly check each other's figures, and this code means they have stopped agreeing.

That is worth knowing because neither computer has to be faulty for it to happen. A single sensor that both of them read, giving a slightly different answer to each, is enough.

Do not let either module be replaced on the strength of this code alone. They are among the most expensive parts on the car and normally have to be programmed to the vehicle. Ask for the other stored codes to be read and dealt with first — a fault naming a specific sensor is almost certainly the real problem.

Was dieser Code bedeutet

A second engine control module is broadcasting data that cannot be accepted as true. See U0400 for the family's framing and U0401 for the first module.

The useful question is which vehicles have a second engine module at all, because the answer changes what this code means.

  • Large V-configuration engines sometimes run a module per bank, each managing its own cylinders while the pair agree about the engine as a whole.
  • Some heavy diesels split engine control from fuel-injection control across two units.
  • Several manufacturers designate a supervisory module as B — the unit that arbitrates between engine, transmission and, on a hybrid, the electric drive.

On a vehicle with only one engine module, this is a configuration problem rather than a fault — software expecting a partner that does not exist, which is what happens when a calibration for a different variant is loaded or a second-hand unit is fitted.

Where two modules genuinely exist, the important point is that they check each other. Each publishes values the other can verify, and the code sets on disagreement — which means neither module need be faulty for it to appear. A sensor read by both, or a figure each computes from a shared input, is enough: one arrives at a slightly different number, the pair stop agreeing, and the check fails.

So the sequence is the family's usual one: read the other stored codes first. A specific sensor fault alongside this is very likely why the two modules stopped agreeing, and replacing either module is an expensive way to discover that.

Wahrscheinliche Ursachen

Hier anfangen

Seltener

Symptome

Beteiligte Bauteile

Information, keine Handlungsanweisung

CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.

Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.

Erfahrungen der Community

Schreiben Sie den ersten Erfahrungsbericht dazu

Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.

Was einen Bericht lesenswert macht:

  • Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
  • Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
  • Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.

Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu U0442.