P2647: Système de l'actionneur de culbuteur A — bloqué activé, banc 1
Ne continuez pas à rouler
Stop driving it and have it looked at, particularly if there is a new tapping or ticking noise from the top of the engine.
The likely symptoms are a rough, lumpy idle and poor low-speed running, or on an engine with cylinder deactivation a persistent misfire feel, vibration and noticeable loss of power because a cylinder has stayed shut down.
The reason for stopping is mechanical rather than about comfort. A mechanism jammed part-way can lose contact with its camshaft lobe and strike it again under valve spring pressure, and camshaft and lifter damage is a known outcome of continuing in that condition. That converts a repair involving a switch or a solenoid into one involving the cylinder head, and the difference is large.
The cheap causes at P2646 are still worth checking first — but check them without driving it around in the meantime.
Ce que signifie ce code
The A rocker arm actuator on bank 1 engaged and did not release. The mechanism is at P2645 and the cost order for investigating it at P2646.
Stuck on is the worse direction, and on a cylinder deactivation engine it is the one that can turn an inexpensive fault into a cylinder head.
What the driver gets depends on the system. On variable valve lift, high lift is held at all times: the idle turns rough and lumpy, low-speed running is poor and fuel consumption rises, because valve timing meant for high revs is badly suited to everything else. On cylinder deactivation, a cylinder stays shut down permanently — the engine runs on fewer cylinders than it has, which reads as a persistent misfire, produces a noticeable vibration and takes a real bite out of the power.
Marked not to be driven, for a mechanical reason rather than a driveability one. An actuator or lifter that is jammed part-way, or releasing unevenly, can lose contact with its cam lobe and then meet it again under valve spring load. Camshaft and lifter damage is a documented outcome of running these systems in that state, and once a lobe is worn the repair is no longer the solenoid or the switch — it is the top of the engine. The gap between those two bills is what the warning is for.
A tapping or ticking noise that has appeared alongside this code is a reason to stop rather than to continue and see.
Causes probables
Commencez ici
- Actionneur de culbuteur défectueux · spécialisée
- Électrovanne de commande de levée de soupape défectueuse · modérée
- Huile moteur insuffisante ou sale · facile
Moins fréquent
- Crépine de l'électrovanne de levée de soupape obstruée · facile
- Manocontact de levée de soupape défectueux · facile
- Came ou poussoir d'arbre à cames usé · spécialisée
Symptômes
Composants concernés
Des informations, pas des instructions
CarGeek est un ouvrage de référence, pas un manuel d'atelier. Ses pages sont rédigées à partir de sources publiques et de ce que d'autres ont constaté, jamais à partir de la documentation technique du constructeur ; elles peuvent donc être erronées ou incomplètes pour votre véhicule précis. Une partie de ce qu'elles décrivent présente un risque réel : haute tension, carburant sous pression, énergie accumulée, pièces chaudes ou en mouvement.
Avant d'agir sur quoi que ce soit, faites-le vérifier par une personne formée, en suivant la procédure du constructeur pour votre véhicule. Rien ici ne remplace cette procédure.
Expérience de la communauté
Soyez le premier à en faire le compte rendu
Rien n'a encore été publié à ce sujet. Tout ce que vous avez trouvé mérite d'être noté — même une impasse épargne à quelqu'un le même après-midi.
Ce qui rend un compte rendu utile :
- La voiture — marque, modèle, année et moteur. La même panne ne se comporte pas pareil sur chacune.
- Ce que vous avez mesuré, pas seulement ce que vous avez remplacé.
- Ce qui a réellement résolu le problème — ou que rien ne l’a résolu, ce qui est utile aussi.
Se connecter ou créer un compte pour ajouter ce que vous avez trouvé à propos de P2647.