P013E: Lambdasonde — Verzögerte Reaktion von fett nach mager, Bank 1 Sensor 2
Was zu tun ist
Ask for the exhaust to be checked for leaks ahead of the sensor. A leak lets air into the exhaust and makes the sensor respond late, and it is a common cause of this fault with a perfectly good sensor — often audible as a ticking or blowing noise, loudest when the engine is cold.
Mention any exhaust work the car has had, since a sensor not screwed fully home or fitted into the wrong port produces this directly.
Mention whether the engine burns oil. Oil ash builds up over the sensor's protective shield and slows it down physically.
The car will usually drive normally. This affects emissions monitoring rather than running, so plan the repair around your MOT rather than treating it as urgent.
Was dieser Code bedeutet
The downstream oxygen sensor on bank 1 is not beginning its rich-to-lean transition when it should.
Delayed response measures dead time — the gap between the mixture actually changing and the sensor noticing. That is a different fault from a sensor that responds slowly once it starts, and it points somewhere different.
Dead time usually means the gas is not reaching the sensor promptly, or is not the gas the module thinks it is.
- An exhaust leak upstream lets fresh air in and dilutes the sample, so the transition arrives blurred and late.
- A sensor not seated to depth, or sitting in a pocket rather than the flowing stream, sees the gas after the main flow has passed.
- A build-up of soot or oil ash over the sensor's protective shield physically slows gas exchange around the element while leaving its electrical behaviour intact.
The direction is diagnostic too, and this is the rich-to-lean case. Contamination on the element tends to hold a sensor rich, because the residue continues to consume oxygen at the surface after the exhaust has gone lean. A delay that is markedly worse in this direction than the other points at a fouled element rather than at a leak, which would delay both roughly equally.
So compare the two directions before deciding. A sensor delayed in one direction only is telling you something a sensor delayed in both is not.
Wahrscheinliche Ursachen
Hier anfangen
- Abgasleck stromaufwärts der Sonde · mittel
- Lambdasonde nicht korrekt eingeschraubt · mittel
- Alternde oder träge Lambdasonde · mittel
Seltener
- Metallspäne an der Sensorspitze · mittel
- Motor verbrennt Öl in den Abgastrakt · Fachwerkstatt
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P013E.