P244D: Auspufftemperatur — Zu hoch für die Regeneration des Partikelfilters, Bank 1
Was zu tun ist
Stop driving hard and get this looked at promptly. The exhaust has run hot enough that the system aborted deliberately to avoid melting the filter, and the conditions that caused it have not gone away.
If you have been ignoring a particulate filter warning light, say so. It is the single most useful thing you can tell the garage here — a heavily loaded filter is the commonest reason temperature runs away, and knowing how long the light has been on tells them what to expect when they inspect it.
Avoid parking over long grass or anything flammable until it is repaired. An exhaust running at regeneration temperature is genuinely hot enough to be a fire risk, which is why some manufacturers warn about it explicitly.
Expect the filter itself to be inspected, not just the sensor. Asking whether it survived is a fair question, and the answer changes the cost of the job considerably.
Was dieser Code bedeutet
Exhaust temperature during a particulate filter regeneration has exceeded the safe limit, and the regeneration has been abandoned to protect the filter.
A regeneration is a controlled fire. Extra fuel raises exhaust temperature to somewhere around 600°C so that trapped soot burns away. The control is the important word — above roughly 800°C the ceramic substrate itself begins to melt, and a melted filter is a replacement.
The usual reason temperature runs away is that there was too much soot to burn. A filter that has been allowed to load heavily, then finally gets a regeneration, releases far more heat than the strategy expected. This is why an ignored particulate filter warning becomes an expensive repair — the warning asks for a drive that would have burned off a manageable amount.
The other explanations are worth checking in order.
- A faulty temperature sensor reporting high when the exhaust is not, which is the cheapest outcome.
- A leaking or stuck-open injector putting far more fuel into the cylinder than the regeneration strategy asked for.
- A post-injection or aftertreatment injector delivering too much fuel directly into the exhaust.
Do not simply clear this and continue. If the temperature genuinely reached the limit, the filter may already be damaged, and the next attempt starts from a filter that is still full.
Wahrscheinliche Ursachen
Hier anfangen
- Abgasanlage während der Regeneration tatsächlich überhitzt · Fachwerkstatt
- Partikelfilter stark mit Ruß beladen · mittel
Seltener
- Einspritzventil undicht · Fachwerkstatt
- Abgastemperatursensor defekt · mittel
- Zu große Nacheinspritzmenge · Fachwerkstatt
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P244D.