C0046: Bremsdrucksensor A und B
Was zu tun ist
The ordinary brakes are unaffected — what has switched off is the system that catches a skid for you. The car will feel completely normal until the moment it would have intervened, which is exactly when you will not want it missing. Drive gently in the wet and cold and get it diagnosed.
Was dieser Code bedeutet
Brake pressure sensors A and B disagree with each other.
This is a correlation code, and it is a different kind of finding from a circuit fault.
Both sensors are answering, and their answers do not match. Neither is obviously dead, so the module cannot tell which one is lying — which is precisely why two were fitted, and precisely why it must now distrust both and shut down.
Do not read this as "sensor C". The title names two designators, A and B, in one code. Reading the position as the third in a lettered run would point at a part that does not exist.
Brake pressure sensors let the module know how hard you are braking, in units it can act on.
Stability control needs the number. To decide whether to add brake pressure at one wheel it has to know what pressure is already there — and to add pressure with the pedal untouched it needs to know it succeeded. Hill-hold, autonomous braking and regenerative blending all read the same sensor.
A pressure sensor is threaded into the hydraulic circuit, usually in the modulator, so replacing one opens the brake system and the brakes must be bled afterwards. That is why it is a specialist job on a part that looks trivial.
The most important thing first: the car still stops.
ABS, traction control and stability control are all additions to a braking system that works without them. When the module finds a fault it switches itself off and hands back a conventional, fully hydraulic brake system — the pedal, the master cylinder, the lines and the calipers are untouched. You have not lost your brakes.
What you have lost is the help. Without ABS the wheels can lock under hard braking, which lengthens the stopping distance on a slippery surface and — the part people forget — takes away your ability to steer while braking hard, because a locked wheel cannot generate cornering force. Without stability control the car will not catch a slide for you.
So drive it, but drive it as though it were forty years old: brake earlier, leave more room, and be especially careful in rain, snow and on gravel.
Wahrscheinliche Ursachen
Hier anfangen
- Bremsdrucksensor defekt · Fachwerkstatt
- Korrodierter oder loser Stecker · Fachwerkstatt
- Kabelbaum beschädigt · Fachwerkstatt
Seltener
- Leitungsbruch in der Sensorleitung · Fachwerkstatt
- ESP-Steuergerät defekt · Fachwerkstatt
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu C0046.