P051D: Kurbelgehäusedrucksensor A — Stromkreis hoch
Was zu tun ist
Ask for the connector to be checked first — including simply that it is plugged in. This sensor sits on the cam cover on many engines, which comes off for spark plugs and gasket work, so one left disconnected after servicing is a common and free-to-fix cause.
Mention any recent work on the top of the engine, however unrelated it seems.
Ask for the sensor's earth connection to be tested, not just its signal wire. A lost earth makes the signal read high and is easy to miss.
Ask for the breather system to be checked at the same time. While this sensor is faulty nothing is watching for a blocked crankcase breather — which is the fault it exists to catch, and the one that pushes oil past the crankshaft seals.
Was dieser Code bedeutet
The crankcase pressure sensor's signal is above the highest voltage the circuit should produce.
High and open are indistinguishable from inside the module, because these inputs carry a pull-up the module sees whenever nothing is loading the circuit. The measurement that separates them is made at the connector with the sensor unplugged, and it takes a minute.
The trivial cause deserves eliminating first. This sensor is mounted on the cam cover on many engines, and the cam cover comes off for spark plugs, coil packs, gaskets and breather work — so a sensor left unplugged after routine servicing is a genuinely common finding and costs nothing to check.
Beyond that, the ordinary open-circuit causes apply: a corroded terminal that has lost contact, a wire broken inside intact insulation where the loom flexes, or a lost earth floating the signal high.
Check the sensor's ground rather than only its signal wire. It is easy to overlook and produces exactly this reading.
A sensor failed internally open is the honest last conclusion. It happens, but everything above it is cheaper and more likely.
Do not skip the breather check while you are there. This sensor's whole purpose is to notice a blocked or disconnected crankcase ventilation system, and a fault in its circuit means nothing is watching for that — which is the real cost of leaving it.
Wahrscheinliche Ursachen
Hier anfangen
- Leitungsbruch in der Sensorleitung · mittel
- Sensor nach früheren Arbeiten nicht wieder angeschlossen · einfach
- Korrodierter oder loser Stecker · einfach
Seltener
- Massekreis des Sensors unterbrochen · mittel
- Kurbelgehäusedrucksensor defekt · mittel
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P051D.