P064C: Glühkerzensteuergerät 1
Was zu tun ist
Ask for the glow plugs themselves to be tested before the control module is replaced. A plug that has gone short circuit can destroy the module's output — and a new module fitted without finding that short fails the same way.
Expect hard starting in cold weather, white smoke, and rough running for the first minute or two. On a modern diesel the glow plugs keep working after the engine starts to control emissions, so this is an emissions fault as well as a starting one.
Mention how the car behaves on a cold morning specifically, since that is when this fault shows itself.
Ask for the module's connector and earth to be inspected, as these carry heavy current and fail at the connections.
Was dieser Code bedeutet
A fault has been reported by or about the first glow plug control module.
Glow plugs are no longer simply switched on for a few seconds before cranking, and understanding what changed explains this whole family of codes. A modern glow plug control module drives each plug individually with a pulse-width-modulated supply, controlling its temperature precisely — and it keeps them running for minutes after the engine has started.
That post-start glowing is emissions work rather than starting help. It keeps combustion stable while the engine is cold, which cuts the white smoke and the unburnt hydrocarbons a cold diesel would otherwise produce. Which is why a glow plug fault is an emissions fault on a modern diesel and not merely a cold-starting inconvenience.
The module also measures each plug's resistance to work out its temperature, and reports faults per cylinder — which is where the rest of this block's glow plug codes come from.
A module fault is often the consequence of a plug rather than its own failure. A glow plug that has gone short circuit drags its driver down and can destroy it, so measure the plugs before replacing the module — otherwise the new one meets the same short.
These modules sit in a hot part of the engine bay and carry heavy current, so check the connector for heat damage and the earth for corrosion before condemning the unit.
Wahrscheinliche Ursachen
Hier anfangen
- Glühkerze ausgefallen · mittel
- Glühzeitsteuergerät ausgefallen · mittel
- Korrodierter oder loser Stecker · einfach
Seltener
- Sicherung des Glühkreises durchgebrannt · einfach
- Schlechte Masseverbindung des Sensors · mittel
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P064C.