U0086: Kommunikationsbus des Fahrzeugs F — (−) niedrig
Was zu tun ist
Expect equipment on the converted part of the vehicle to have stopped or to be misbehaving, and probably worse when the equipment is running.
That load-related pattern is the clue, and there is a one-minute test that confirms it.
Ask for the voltage between the vehicle body and the chassis to be measured while the body equipment is running. A good bonding shows a few tens of millivolts. A corroded one shows whole volts — and volts between two parts of a vehicle that should be at exactly the same potential is the fault, stated as plainly as it can be.
That is far simpler and more decisive than tracing network wiring, and it should be the first thing done on a converted vehicle with this code.
The cause is the earth strap between body and chassis — the connection that carries everything the body equipment draws, living under the vehicle in the salt. It is accessible and cheap, which is the best combination there is.
Say whether the problem is worse when the equipment is working, since that is what points here.
Was dieser Code bedeutet
The negative line of vehicle communication bus F is being held low. Everything at U0083 applies, including that the body-to-chassis earth strap is the commonest single cause on this kind of vehicle and should be inspected before the bus pair is traced.
One addition belongs to this conductor: it is the one nearest the earth wiring, so a degraded body earth reaches it first — which is why the U0083 signature of a fault that follows load rather than movement shows up here most clearly.
And there is a check that separates the two possibilities in a minute. Measure the voltage between the body structure and the chassis with the body equipment running. A healthy bonding shows a few tens of millivolts. A corroded one shows volts — and volts between two parts of a vehicle that should be at the same potential is the fault, stated directly.
That is a simpler and more decisive test than tracing a network, and it is the one to ask for first on a converted vehicle showing this code.
Wahrscheinliche Ursachen
Hier anfangen
- Masseverbindung korrodiert · mittel
- Leitung mit Masse kurzgeschlossen · mittel
- Schlechte Leitungsverbindung in einem nachträglichen Einbau · mittel
- Datenbusleitungen beschädigt · mittel
Seltener
- Wasser in den Stecker eingedrungen · mittel
- Zeitweiliger Fehler in der Verkabelung · mittel
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu U0086.