U0127: Kommunikationsverlust mit dem Reifendruckkontrollmodul
Was zu tun ist
The car drives normally. What you have lost is the warning that a tyre is going down — so until it is fixed, check your tyre pressures yourself with a gauge, about once a month, when the tyres are cold. The correct pressures are on a sticker in the driver's door frame or inside the fuel filler flap. That takes five minutes and covers the gap completely.
Worth asking which type of system the car has, because it changes the repair. If there are sensors inside the wheels, they contain sealed batteries that last around five to ten years and cannot be replaced separately — so on an older car this can simply be age. If the system works from the wheel speed sensors instead, there are no sensors to fail, and it needs resetting manually every time a tyre is inflated or changed.
In many places a tyre pressure monitoring system that does not work will fail a roadworthiness test on a car required to have one.
Was dieser Code bedeutet
The tyre pressure monitoring module has stopped being heard from. The general reasoning is at U0100.
Nothing about how the vehicle drives changes. What is lost is the warning that a tyre is going down, and the value of that is entirely in the failure it is designed to catch: a slow puncture that nobody notices until the tyre is destroyed or, worse, until it fails at speed.
Which kind of system a vehicle has decides everything about the repair, and it is worth establishing first.
- Direct systems put a battery-powered sensor inside each wheel, measuring actual pressure. They are accurate, they report real numbers, and the batteries are sealed in and last roughly five to ten years — after which the sensor is replaced whole. A vehicle old enough for this code is often old enough for that to be the real story.
- Indirect systems have no sensors at all. They infer a soft tyre from wheel speed, because a tyre losing pressure has a smaller rolling radius and turns fractionally faster. Cheaper, nothing to go flat, and no absolute pressures — which is why they must be reset manually after inflating or changing a tyre, and why they cannot notice all four going down together.
In the meantime the remedy is free and old-fashioned: check the pressures with a gauge. Monthly, cold, against the placard in the door frame or filler flap. That is what the system automates rather than replaces.
Worth noting that in many jurisdictions a non-functioning tyre pressure monitoring system is a roadworthiness test failure on vehicles required to have one.
Wahrscheinliche Ursachen
Hier anfangen
- Korrodierter oder loser Stecker · einfach
- Datenbusleitungen beschädigt · mittel
- Versorgung oder Masse des Steuergeräts ausgefallen · mittel
Seltener
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu U0127.