U0513: Ungültige Daten vom Modul des Gierratensensors empfangen
Was zu tun ist
Expect the stability control light to be on, and treat the car as if it has none — because it has. It drives normally; what has gone is the electronic safety net that intervenes when a car starts to slide.
Drive accordingly until it is fixed: more room in the wet, gentler on cold or greasy roads, no sudden corrections. Nothing about the car feels different, which is exactly the trap — the difference only appears at the moment you would have needed the system.
Mention any recent work. This sensor lives inside the car, usually under a console or a seat, and it must be bolted down tight and the right way round. Interior work, seat removal, or an alignment are the usual triggers — often a bracket left loose or a calibration step skipped rather than a failed part.
Was dieser Code bedeutet
The yaw rate sensor module is broadcasting data that cannot be accepted as true. See U0400 for what an invalid-data code is and why the module it names is usually the messenger rather than the culprit.
This is the one code in this range that is genuinely about how the car behaves, and it deserves more attention than its neighbours.
A yaw rate sensor measures how fast the car is rotating about its vertical axis — how quickly it is turning — and stability control compares that against where the steering is pointed and how fast the wheels are going. When those three disagree, the system decides the car is sliding and brakes individual wheels to correct it.
So a yaw sensor publishing implausible values leaves stability control with no basis to act, and the system does the only safe thing: it switches itself off and lights the dashboard. The car then handles as a car without stability control, which is to say normally right up until the moment it would have needed it.
The commonest cause is not the sensor. It is mounting: the sensor must be rigidly attached, in a known orientation, usually near the centre of the car under a console or seat. A loose bracket, a bolt left finger-tight after interior work, or a sensor refitted the wrong way round produces exactly this code from a perfectly good part.
The second cause is calibration. After suspension work, an alignment, or a sensor replacement, many systems need a stationary zero-point learn. Skipping it leaves the module reporting a permanent slow rotation while the car sits still, which is precisely the kind of impossible value this family names.
Wahrscheinliche Ursachen
Hier anfangen
- Gierratensensor defekt · mittel
- Sensor nach dem Tausch nicht angelernt · Fachwerkstatt
- Korrodierter oder loser Stecker · einfach
Seltener
- Datenbusleitungen beschädigt · mittel
Selten
- ESP-Steuergerät defekt · Fachwerkstatt
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu U0513.