P2600: Kühlmittelpumpe A — Steuerstromkreis unterbrochen
Was zu tun ist
The car may drive entirely normally, and that is exactly why this is worth dealing with promptly rather than leaving. On a turbocharged engine this pump usually keeps running for a few minutes after you switch off, and that run-on is what stops heat soaking into the turbocharger and baking the oil in its bearing. Losing it does no harm on any single journey and does real harm over months, invisibly, after the car has been parked.
Two things to watch for and report. If the heater goes cold whenever the engine stops at a junction and warms up again as it restarts, that is this fault — the electric pump is what keeps hot coolant moving while the engine is off. And keep an eye on the temperature gauge in slow traffic, since an electric pump is doing most of the work at low speeds.
Ask for the fuse, the connector and the wiring to be checked before the pump is replaced; an open circuit is more often one of those than the pump itself.
Was dieser Code bedeutet
An open circuit in the control output driving an electrically powered coolant pump.
A belt-driven water pump has one flaw that no amount of engineering can remove: its speed is tied to engine speed, and that relationship is backwards. An engine needs the most cooling when it is working hard at low speed — crawling in traffic on a hot day, towing up a long climb — which is exactly when a belt pump is turning slowly and the airflow through the radiator is weakest. At a motorway cruise it needs relatively little, and the pump is spinning fast. An electric pump breaks that link: it runs at whatever rate the module asks for, based on temperature rather than on engine speed.
The more important thing it can do is run when the engine is not running at all, and that is where a fault here becomes expensive in a way nobody sees coming.
On a turbocharged engine, shutting down is the hottest moment the turbocharger experiences. While the engine runs, oil and coolant carry heat away from the bearing housing continuously. Switch off, and that flow stops while the turbine — which has just been glowing — is still soaking heat back into the housing. If nothing moves the coolant, it boils where it sits and the oil in the bearing housing bakes onto the shaft as carbon. This is the slow mechanism behind a large share of turbocharger failures, and the run-on pump exists to prevent it. It cycles for a few minutes after the key is turned off, which is why a modern car sometimes hums quietly to itself in a garage.
So a failed pump control circuit can be damaging a turbocharger after the driver has parked and walked away, with nothing wrong while driving. The temperature gauge is normal, the engine behaves perfectly, and the harm is done in a car park. That is an unusual failure shape and it is the reason this code is worth acting on rather than filing.
The same pump does other work on vehicles that stop their engines: on a stop-start car or a hybrid the engine is frequently off while the cabin still wants heat, and only an electric pump can keep the heater matrix supplied. A heater that goes cold every time the engine stops at a junction, and warms again as it restarts, is this fault rather than a heating fault.
An open circuit means the module's command never reaches the pump. The connector, the wiring and the pump's own supply fuse are the ordinary places to look before the pump itself.
Wahrscheinliche Ursachen
Hier anfangen
- Leitungsbruch in der Steuerleitung · mittel
- Sicherung durchgebrannt oder Versorgung ausgefallen · einfach
- Korrodierter oder loser Stecker · einfach
- Elektrische Kühlmittelpumpe defekt · mittel
Seltener
- Kabelbaum beschädigt · mittel
Selten
- Motorsteuergerät defekt · Fachwerkstatt
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P2600.