U0084: Kommunikationsbus des Fahrzeugs F — (+) hoch
Was zu tun ist
Isolate the body equipment before doing anything else, and do not operate it until this is fixed.
Full battery voltage has got onto a network wire, and every computer on that network is connected to it — see U0005.
On a converted or commercial vehicle this is more serious than on a car, and the reason is the current available. A tail-lift, crane, tipper pump or winch runs on very heavy cable, and that cable is often routed alongside the network wiring, under the vehicle where road damage and corrosion reach it. A network wire touching a lighting circuit is a fault. One touching a winch feed is a fault fed by a cable that will not blow a fuse before the damage is done.
So expect the repair to have two stages — the short found and fixed, and then an assessment of what survived — and treat that as likely rather than possible.
One free test comes first: disconnect the body equipment and re-check. On this kind of vehicle that genuinely isolates half the wiring, which makes it a more decisive test than it would be on a car.
Contact whoever converted the vehicle, since that wiring is theirs.
Was dieser Code bedeutet
The positive line of vehicle communication bus F is being held high. See U0005 for the module-damage warning — battery voltage on a bus wire can destroy the transceiver in every module on that network, so the repair may have two stages.
On a converted vehicle this fault has a source cars do not have: high-current body circuits.
A tail-lift, a crane, a tipper pump or a winch draws tens or hundreds of amps, on cable sized accordingly, run by whoever built the body. That cable is often in the same run as the network wiring, and it is under a vehicle rather than inside a cabin — so chafe, road damage and corrosion all reach it.
And the consequence scales with the current. A network wire chafed against a lighting circuit is a fault. One chafed against a winch feed is a fault applied through a cable that will not blow a fuse before the transceivers are gone.
So on this kind of vehicle the two-stage warning at U0005 is not a possibility but an expectation, and the sequence matters: isolate the body equipment, find the short, then assess what survived.
And the free first test remains: disconnect the body equipment and re-check. On a converted vehicle that is a genuine isolation of one half of the wiring, and it is more decisive than it is on a car.
Wahrscheinliche Ursachen
Hier anfangen
- Schlechte Leitungsverbindung in einem nachträglichen Einbau · mittel
- Leitung mit Spannung kurzgeschlossen · mittel
- Kabelbaum beschädigt · mittel
- Datenbusleitungen beschädigt · mittel
Seltener
- Mechanische Beschädigung durch Steinschlag · mittel
- Masseverbindung korrodiert · mittel
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu U0084.