P2163: Funktion des oberen Anschlags von Positionssensor A und B von Drosselklappe oder Pedal
Was zu tun ist
The car will usually drive with reduced power rather than stop. If this appeared after throttle body cleaning, an air intake repair or a relearn procedure, say so — a stop learned incorrectly during that work is a repeat of the procedure, not a new throttle body. Cleaning is much less likely to be the answer here than for the closed-throttle codes, because the plate does not collect carbon at the open end.
Was dieser Code bedeutet
The position reading at the fully open end of travel is not where the module expects it to be. This is the counterpart to the minimum stop codes at P2109 and P2113, and the two ends fail for different reasons — which is what makes knowing the end useful.
A throttle has two mechanical stops, and the module treats them as calibration references. They are physical: screws or moulded limits that the plate rests against, and their positions are learned and stored so the module knows what its sensor voltages mean in degrees. Everything the throttle does afterwards is measured against them.
The minimum stop drifts because of carbon. Deposits build up around the plate at the closed end, where the plate spends most of its life and where crankcase and recirculated gases condense. That is the common one, and it is why the corpus keeps returning to throttle cleaning.
The maximum stop does not accumulate carbon — the plate is nowhere near it in normal driving, and airflow at full open keeps it clean. So a maximum stop that has moved is usually saying something has changed mechanically or electrically, not that the throttle is dirty: a bent or damaged plate, a stop adjusted by hand at some point in the vehicle's history, a sensor track worn at the end it is least often driven to, or a relearn performed while something was obstructing full travel.
That last one deserves attention, because it is self-inflicted and common: a relearn carried out with the air intake ducting disconnected, or with a hand resting on the linkage, stores a maximum stop that the throttle can never reach again.
Wahrscheinliche Ursachen
Hier anfangen
Seltener
- Drosselklappe beschädigt oder verbogen · mittel
- Drosselklappenstutzen defekt · mittel
- Fremdkörper im Drosselklappenstutzen · einfach
Selten
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P2163.