U0031: Kommunikationsbus des Fahrzeugs A — (+) niedrig
Was zu tun ist
Expect a group of systems to have stopped working together. A network wire is being held down by a short to the bodywork, so messages cannot get through.
Two things are worth telling the garage.
Has anything been fitted to the car — a tracker, dashcam, alarm, stereo, tow bar or insurance box? An earth connection added beside the network wires, or a screw through the loom, causes a lot of these, and unplugging the device to re-test is far quicker than stripping trim.
And did the fault come and go before becoming permanent? That is typical of a wire rubbing through against bodywork, and it tells a technician to move the loom by hand rather than reach for a meter.
Do not let computers be replaced on the strength of the long fault list — they are almost certainly all fine, and are simply reporting that they cannot hear each other.
Was dieser Code bedeutet
The positive line of vehicle communication bus A is being held low. See U0004 for the short-to-earth argument and the voltage signature, and U0028 for identifying the bus first.
The voltage test is the one that survives not knowing which network this is, and that is worth saying because everything else on a lettered bus depends on identification.
Resistance figures vary between networks; the shape of a differential signal does not. Both conductors idling at the same voltage and moving symmetrically is what every one of these buses does, whatever its speed. So a conductor sitting at zero and not moving is shorted to earth on any of them — and that can be established before the network has been named.
Where the short is follows U0004: a conductor chafed through against the body, a bracket or a panel edge, which is why the fault often follows the loom's route rather than any component, and why moving the harness by hand finds it faster than a meter when it is currently present.
And an aftermarket earth taken beside the pair remains worth eliminating first, because unplugging a device is quicker than stripping trim.
Wahrscheinliche Ursachen
Hier anfangen
- Leitung mit Masse kurzgeschlossen · mittel
- Datenbusleitungen beschädigt · mittel
- Schlechte Leitungsverbindung in einem nachträglichen Einbau · mittel
- Kabelbaum beschädigt · mittel
Seltener
- Wasser in den Stecker eingedrungen · mittel
- Ein anderes Steuergerät zieht den Bus auf Masse · Fachwerkstatt
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu U0031.