U0009: Barramento de comunicação CAN de alta velocidade — (−) em curto com o barramento (+)
Não continue dirigindo
The car may crank but not run, with a dead dashboard, and a garage that says their diagnostic tool cannot connect at all.
That combination is this fault almost exactly. The two wires carrying your car's internal network are touching each other, and because they carry the same message in opposite directions, joining them cancels the signal completely. The network does not work badly — it stops. Your lights, horn and starter still work because they are not on it.
There is a free test that confirms it beyond doubt, and it is worth asking for by name: the resistance across pins 6 and 14 of the diagnostic socket. A healthy car reads about 60 ohms; a car with this fault reads close to zero. No interpretation needed.
Two wires that are twisted together only touch for physical reasons, and the list is short. A loom crushed by a panel, a seat bolt or a bracket. A screw or trim clip put through the harness during a repair or an accessory installation. Water bridging a connector. Rodents.
And one free check first if you tow: unplug the trailer and look inside the socket. A trailer socket full of water is a recognised cause on vehicles whose network runs nearby, and that takes a minute rather than an afternoon.
The car will need recovering. Do not let computers be replaced — they are almost certainly all fine.
O que este código significa
The two lines of the high speed data bus are shorted together. See U0003 for the pair and the resistance test.
This is the fault the resistance test identifies most decisively, and it is worth knowing because the reading is unmistakable. A healthy bus reads about 60 ohms across pins 6 and 14 of the diagnostic socket. A pair shorted together reads close to zero. There is no ambiguity and no interpretation required.
And the consequence is total. The two wires carry the same signal inverted, so joining them means each cancels the other exactly — there is no difference left to read, anywhere on the vehicle. The network does not degrade; it stops.
Which is why the presenting picture is a vehicle that appears completely dead electronically while its lights, horn and starter may all still work. Those are not on the bus. A car that cranks but will not run, with a dead dashboard and a scan tool that cannot connect, is describing this exactly.
Where two wires that are twisted together end up joined is nearly always physical, and the list is short:
- A crush. A loom trapped by a panel, a seat bolt, a bracket or a jacking point.
- A fastener through the harness. A screw fitted during a repair, a trim clip, a self-tapper from an accessory installation.
- Water bridging a connector. Rarely enough on its own to read as a dead short, but enough to stop the bus — and it is why a bus fault appearing after heavy rain or a flooded footwell should be looked for at a connector rather than along a wire.
- Rodent damage, where the insulation is gone from both conductors at the same point.
And one route worth naming because it is common on towing vehicles. A trailer socket full of water, on a vehicle whose bus is routed nearby, is a recognised cause — so unplug any trailer and check the socket before searching the vehicle. That is free and it settles a proportion of these.
Causas prováveis
Comece aqui
- Fios do barramento em curto entre si · moderado
- Chicote elétrico danificado · moderado
- Infiltração de água no conector · moderado
- Fiação do barramento de dados danificada · moderado
Menos comum
- Emenda de fiação malfeita em instalação de terceiros · moderado
- Conector corroído ou frouxo · fácil
Sintomas
Componentes envolvidos
Informação, não instrução
O CarGeek é uma referência, não um manual de serviço. Suas páginas são escritas a partir de fontes públicas e do que outras pessoas constataram, nunca a partir da documentação de serviço do fabricante, de modo que podem estar erradas ou incompletas para o seu veículo específico. Parte do que descrevem envolve risco real: alta tensão, combustível sob pressão, energia acumulada e peças quentes ou em movimento.
Antes de agir com base em qualquer orientação, peça a verificação de uma pessoa com formação técnica, seguindo o procedimento do próprio fabricante para o seu veículo. Nada aqui substitui esse procedimento.
Experiência da comunidade
Seja o primeiro a documentar isto
Ainda não há publicações sobre isto. Vale a pena anotar tudo o que você descobriu — até um beco sem saída poupa a mesma tarde de outra pessoa.
O que faz valer a leitura:
- O carro — marca, modelo, ano e motor. A mesma falha se comporta de forma diferente em cada um.
- O que você mediu, não só o que trocou.
- O que realmente resolveu — ou que nada resolveu, o que também vale saber.
Entrar ou criar uma conta para adicionar o que você descobriu sobre U0009.