U0009: CAN-communicatiebus hoge snelheid — (−) kortgesloten met bus (+)
Niet doorrijden
The car may crank but not run, with a dead dashboard, and a garage that says their diagnostic tool cannot connect at all.
That combination is this fault almost exactly. The two wires carrying your car's internal network are touching each other, and because they carry the same message in opposite directions, joining them cancels the signal completely. The network does not work badly — it stops. Your lights, horn and starter still work because they are not on it.
There is a free test that confirms it beyond doubt, and it is worth asking for by name: the resistance across pins 6 and 14 of the diagnostic socket. A healthy car reads about 60 ohms; a car with this fault reads close to zero. No interpretation needed.
Two wires that are twisted together only touch for physical reasons, and the list is short. A loom crushed by a panel, a seat bolt or a bracket. A screw or trim clip put through the harness during a repair or an accessory installation. Water bridging a connector. Rodents.
And one free check first if you tow: unplug the trailer and look inside the socket. A trailer socket full of water is a recognised cause on vehicles whose network runs nearby, and that takes a minute rather than an afternoon.
The car will need recovering. Do not let computers be replaced — they are almost certainly all fine.
Wat deze code betekent
The two lines of the high speed data bus are shorted together. See U0003 for the pair and the resistance test.
This is the fault the resistance test identifies most decisively, and it is worth knowing because the reading is unmistakable. A healthy bus reads about 60 ohms across pins 6 and 14 of the diagnostic socket. A pair shorted together reads close to zero. There is no ambiguity and no interpretation required.
And the consequence is total. The two wires carry the same signal inverted, so joining them means each cancels the other exactly — there is no difference left to read, anywhere on the vehicle. The network does not degrade; it stops.
Which is why the presenting picture is a vehicle that appears completely dead electronically while its lights, horn and starter may all still work. Those are not on the bus. A car that cranks but will not run, with a dead dashboard and a scan tool that cannot connect, is describing this exactly.
Where two wires that are twisted together end up joined is nearly always physical, and the list is short:
- A crush. A loom trapped by a panel, a seat bolt, a bracket or a jacking point.
- A fastener through the harness. A screw fitted during a repair, a trim clip, a self-tapper from an accessory installation.
- Water bridging a connector. Rarely enough on its own to read as a dead short, but enough to stop the bus — and it is why a bus fault appearing after heavy rain or a flooded footwell should be looked for at a connector rather than along a wire.
- Rodent damage, where the insulation is gone from both conductors at the same point.
And one route worth naming because it is common on towing vehicles. A trailer socket full of water, on a vehicle whose bus is routed nearby, is a recognised cause — so unplug any trailer and check the socket before searching the vehicle. That is free and it settles a proportion of these.
Waarschijnlijke oorzaken
Begin hier
- Buskabels onderling kortgesloten · gemiddeld
- Kabelboom beschadigd · gemiddeld
- Water binnengedrongen in de connector · gemiddeld
- Bedrading van de databus beschadigd · gemiddeld
Minder vaak
- Slechte lasverbinding in een naderhand aangebrachte installatie · gemiddeld
- Gecorrodeerde of losse stekker · eenvoudig
Symptomen
Betrokken onderdelen
Informatie, geen instructie
CarGeek is een naslagwerk, geen werkplaatshandboek. De pagina's zijn geschreven op basis van openbare bronnen en van wat anderen hebben ondervonden, nooit op basis van de servicedocumentatie van de fabrikant zelf, dus ze kunnen onjuist of onvolledig zijn voor jouw specifieke voertuig. Een deel van wat erin staat brengt echt gevaar met zich mee: hoogspanning, brandstof onder druk, opgeslagen energie en hete of bewegende delen.
Laat alles waarnaar je wilt handelen eerst controleren door iemand met een technische opleiding, aan de hand van de eigen procedure van de fabrikant voor jouw voertuig. Niets hier vervangt die procedure.
Ervaring uit de community
Wees de eerste die dit beschrijft
Hierover is nog niets geplaatst. Wat je ook hebt gevonden, het is het opschrijven waard — zelfs een doodlopend spoor bespaart iemand dezelfde middag.
Wat het de moeite waard maakt:
- De auto — merk, model, bouwjaar en motor. Dezelfde storing gedraagt zich per auto anders.
- Wat je gemeten hebt, niet alleen wat je vervangen hebt.
- Wat het echt verholpen heeft — of dat niets dat deed, wat ook nuttig is om te weten.
Inloggen of een account aanmaken om toe te voegen wat je hebt gevonden over U0009.