P272D: Motor der Parksperrenklinke — Strom des Steuerstromkreises zu hoch
Was zu tun ist
Always apply the parking brake when you park — do not rely on P. The car may not be able to engage or confirm the park lock. When parking, come to a full stop, apply the parking brake, and only then select P; doing it in that order takes the vehicle's weight off the park mechanism and is worth the habit on a slope. Get it diagnosed promptly.
Was dieser Code bedeutet
The park pawl motor is drawing more current than expected.
The park pawl is the only thing physically stopping a parked car from rolling away, and shift-by-wire made it an electrical component.
It is a steel tooth that drops into a toothed wheel on the output shaft. On a car with a mechanical linkage, moving the lever to P pushes it there through a cable and the driver feels it engage. On shift-by-wire there is no linkage — the lever is a switch, and a motor moves the pawl. Which means the car has to know the pawl engaged, and has to tell the driver when it did not.
That is why these codes matter more than their part cost suggests. A pawl that has not engaged leaves the car held only by the parking brake, and on a slope by nothing at all if the brake is also electric and has not applied.
Excess current means the motor is working against something. That is a mechanical finding rather than an electrical one: the mechanism is stiff, obstructed, or being asked to move when it cannot.
The commonest legitimate cause is parking on a slope. The vehicle's weight loads the pawl against the tooth it dropped into, and the motor may not have the force to withdraw it — which is exactly why the advice for a manual transmission on a hill is to leave it in gear and apply the handbrake, and why an automatic should be brought to a stop on the brake, parking brake applied, and only then put in P. Doing it in that order unloads the pawl and it withdraws freely.
Beyond that: corrosion in the mechanism, a failing motor, or a control module unable to drive it.
Use the parking brake every time while this is stored, and do not assume the car is held by P.
Wahrscheinliche Ursachen
Hier anfangen
- Korrodierter oder loser Stecker · Fachwerkstatt
- Wählmotor der Getriebestufe defekt · Fachwerkstatt
- Kabelbaum beschädigt · Fachwerkstatt
- Parksperrenmechanik festgefressen oder blockiert · Fachwerkstatt
Seltener
- Getriebesteuergerät defekt · Fachwerkstatt
Symptome
Beteiligte Bauteile
Information, keine Handlungsanweisung
CarGeek ist ein Nachschlagewerk, kein Werkstatthandbuch. Die Seiten entstehen aus öffentlichen Quellen und aus dem, was andere festgestellt haben, nie aus den Serviceunterlagen des Herstellers; für Ihr konkretes Fahrzeug können sie daher falsch oder unvollständig sein. Ein Teil des Beschriebenen birgt echte Gefahren: Hochspannung, Kraftstoff unter Druck, gespeicherte Energie sowie heiße oder bewegte Teile.
Lassen Sie alles, wonach Sie handeln wollen, von einer fachlich geschulten Person anhand der herstellereigenen Vorgehensweise für Ihr Fahrzeug prüfen. Nichts hiervon ersetzt diese Vorgehensweise.
Erfahrungen der Community
Schreiben Sie den ersten Erfahrungsbericht dazu
Dazu wurde noch nichts veröffentlicht. Was immer Sie gefunden haben, ist es wert, aufgeschrieben zu werden — selbst eine Sackgasse erspart jemandem denselben Nachmittag.
Was einen Bericht lesenswert macht:
- Das Fahrzeug — Marke, Modell, Baujahr und Motor. Derselbe Fehler verhält sich auf jedem anders.
- Was Sie gemessen haben, nicht nur, was Sie getauscht haben.
- Was es tatsächlich behoben hat — oder dass nichts es behoben hat, was ebenso nützlich ist.
Anmelden oder ein Konto anlegen und eintragen, was Sie gefunden haben — zu P272D.